Minimising Defect Formation in Sand Casting of Sheet Lead: A DoE Approach

Sand casting of lead sheet is a traditional manufacturing process used up to the present due to the special features of sand cast sheet such as their attractive sheen. Similarly to any casting process, sand casting of lead sheet suffers from the presence of surface defects. In this study, a surface defect type, hereby referred to as ‘grooves’, has been investigated. The focus has been laid on the identification of the main factors affecting defect formation in this process. Based on a set of screening experiments performed using Scanning Electron Microscopy (SEM) as well as the existing literature, a number of factors affecting the formation of such defects was identified and their corresponding significance was estimated using the Analysis of Variance (ANOVA) technique. The obtained results suggest that the most significant factor affecting defect formation in sand casting of lead sheet is the composition of the moulding mixture. Defect formation was also proven to be dependent on the sand grain fineness, the quality of the melt and some of the interactions between the aforementioned process parameters. Finally, an optimal set of process parameters leading to the minimisation of surface defects was identified.

[1]  K. Salonitis,et al.  Characterisation of Lead Sheet Manufactured Using Traditional Sand-Casting Technique , 2019, Shape Casting.

[2]  J. A. Charles,et al.  Microstructures and mechanical properties of milled and continuously cast lead sheet , 1991 .

[3]  Uday A. Dabade,et al.  Casting Defect Analysis using Design of Experiments (DoE) and Computer Aided Casting Simulation Technique , 2013 .

[4]  G. Oehlert.  A first course in design and analysis of experiments , 2000 .

[5]  J. H. Hubbell,et al.  Tables of X-Ray Mass Attenuation Coefficients and Mass Energy-Absorption Coefficients 1 keV to 20 MeV for Elements Z = 1 to 92 and 48 Additional Substances of Dosimetric Interest , 1995 .

[6]  J. Campbell.  An overview of the effects of bifilms on the structure and properties of cast alloys , 2006 .

[7]  M Perzyk,et al.  Detection of causes of casting defects assisted by artificial neural networks , 2003 .

[8]  Bhushan Lal Karihaloo,et al.  Comprehensive structural integrity , 2003 .

[9]  Margaret J. Robertson,et al.  Design and Analysis of Experiments , 2006, Handbook of statistics.

[10]  Charnnarong Saikaew,et al.  Optimization of molding sand composition for quality improvement of iron castings , 2012 .

[11]  Amit Sata,et al.  New Approach to Casting Defects Classification and Analysis Supported by Simulation , 2011 .

[12]  Pankaj Chandna,et al.  Optimization of Process Parameters of Pressure Die Casting using Taguchi Methodology , 2012 .

[13]  M. M. Aman,et al.  Application of ANOVA method to study solar energy for hydrogen production , 2019, International Journal of Hydrogen Energy.

[14]  John L. Campbell,et al.  Complete Casting Handbook: Metal Casting Processes, Techniques and Design , 2018 .

[15]  B. Erez,et al.  A new Ghassulian metallurgical assemblage from Bet Shemesh (Israel) and the earliest leaded copper in the Levant , 2016 .

[16]  Emmanuel Rocca,et al.  Study of ancient lead materials: A gallo-roman sarcophagus—contribution of the electrolytic treatment to its restoration , 2004 .

[17]  J. A. Charles,et al.  Microstructures and mechanical properties of milled and continuously cast lead sheet Part 1 Microstructures , 1989 .

[18]  A. Noorul Haq,et al.  Optimization of green sand casting process parameters by using Taguchi’s method , 2006 .

[19]  Fabrizio Scarpa,et al.  Evaluation of hybrid-short-coir-fibre-reinforced composites via full factorial design , 2018, Composite Structures.

[20]  K. Salonitis,et al.  Improving Energy Efficiency in Direct Method for Continuous Casting of Lead Sheets , 2018 .

[21]  Konstantinos Salonitis,et al.  Sand casting of sheet lead: numerical simulation of metal flow and solidification , 2020 .

[22]  Jafri Mohd Rohani,et al.  Application of Six Sigma DMAIC methodology in plain yogurt production process , 2018, International Journal of Lean Six Sigma.

[23]  John R. Brown,et al.  Foseco foundryman's handbook , 1994 .

[24]  U. Natarajan,et al.  Determining the optimum green sand casting process parameters using Taguchi's method , 2012 .

[25]  J. W. van der Touw,et al.  Effect of melt cleanliness on the formation of porosity defects in automotive aluminium high pressure die castings , 2002 .

[26]  W. M. Haynes.  CRC Handbook of Chemistry and Physics , 1990 .