Geometric size effect on IMC growth and elements diffusion in Cu/Sn/Cu solder joints

Purpose The purpose of this paper is to investigate the effect of geometric size on intermetallic compound (IMC) growth and elements diffusion of Cu/Sn/Cu solder joint and establish the correlation model between the thickness of the IMC layer and size of the solder joint on the dozens of microns scale. Design/methodology/approach The sandwich-structured Cu/Sn/Cu solder joints with different gaps between two copper-clad plates (δ) are fabricated using a reflow process. The microstructure and composition of solder joints are observed and analyzed by scanning electron microscopy. Findings After reflow, the thickness of the IMC and Cu concentration in solder layers increase with the reduction of δ from 50, 40, 30, 20 to 10 μm. During isothermal aging, the thickness of the IMC fails to increase according to the traditional parabolic rule due to changes in Cu concentration. The reduction of δ is the root cause of changes in Cu concentration and the growth rule of the IMC layer. A correlation model between the thickness of the IMC layer and δ is established. It is found that the thickness of the IMC layer is the function of aging time and δ. With δ reducing, the main control element of IMC growth transfers from Cu to Sn. Originality/value This paper shows the changes of IMC thickness and elements concentration with the reduction of the size of solder joints on the dozens of microns scale. A correlation model is established to calculate the thickness of the IMC layer during aging.

[1]  Xi Liu,et al.  The size effect on intermetallic microstructure evolution of critical solder joints for flip chip assemblies , 2015 .

[2]  Fengshun Wu,et al.  Effect of stand‐off height on the microstructure and mechanical behaviour of solder joints , 2010 .

[3]  Minghui Chen,et al.  Formation of intermetallic compounds in SnAgBiIn solder systems on Cu substrates , 2009 .

[4]  Ning Zhao,et al.  Viscosity and Surface Tension of Liquid Sn-Cu Lead-Free Solders , 2009 .

[5]  R. Darveaux,et al.  Effect of joint size and pad metallization on solder mechanical properties , 2008, 2008 58th Electronic Components and Technology Conference.

[6]  Young-Bae Park,et al.  Size effect on electromigration reliability of pb-free flip chip solder bump , 2008, 2008 58th Electronic Components and Technology Conference.

[7]  Young‐Chang Joo,et al.  Intermetallic compound and Kirkendall void growth in Cu pillar bump during annealing and current stressing , 2008, 2008 58th Electronic Components and Technology Conference.

[8]  Chak-Kuen Wong,et al.  The influence of solder volume and pad area on Sn-3.8Ag-0.7Cu and Ni UBM reaction in reflow soldering and isothermal aging , 2008, Microelectron. Reliab..

[9]  P. Vianco,et al.  Solid-State Interface Reactions between Silver and 95.5Sn-3.9Ag-0.6Cu and 63Sn-37Pb Solders , 2007 .

[10]  Y. T. Chin,et al.  Effect of Solder Volume on Interfacial Reactions between Eutectic Sn-Pb and Sn-Ag-Cu Solders and Ni(P)-Au Surface Finish , 2006, 2006 Thirty-First IEEE/CPMT International Electronics Manufacturing Technology Symposium.

[11]  T. Takenaka,et al.  Growth behavior of compound layers in Sn/Cu/Sn diffusion couples during annealing at 433–473 K , 2005 .

[12]  P. Conway,et al.  Effect of solder bump geometry on the microstructure of Sn–3.5 wt% Ag on electroless nickel immersion gold during solder dipping , 2005 .

[13]  K. Chiang,et al.  Aging study on interfacial microstructure and solder-ball shear strength of a wafer-level chip-size package with Au/Ni metallization on a Cu pad , 2004 .

[14]  Nikhilesh Chawla,et al.  Influence of initial morphology and thickness of Cu6Sn5 and Cu3Sn intermetallics on growth and evolution during thermal aging of Sn-Ag solder/Cu joints , 2003 .

[15]  King-Ning Tu,et al.  Mean-time-to-failure study of flip chip solder joints on Cu/Ni(V)/Al thin-film under-bump-metallization , 2003 .

[16]  Cheol-Woong Yang,et al.  Intermetallic compound layer formation between Sn–3.5 mass %Ag BGA solder ball and (Cu, immersion Au/electroless Ni–P/Cu) substrate , 2003 .

[17]  H. Reichl,et al.  A study on interfacial reactions between electroless Ni-P under bump metallization and 95.5Sn-4.0Ag-0.5Cu alloy , 2003 .

[18]  P. Vianco,et al.  Intermetallic compound layer formation between copper and hot-dipped 100In, 50In-50Sn, 100Sn, and 63Sn-37Pb coatings , 1994 .