Development of three-dimensional optimization of a small-scale radial turbine for solar powered Brayton cycle application

Abstract Numerical simulation was carried out to optimize the design of a small-scale radial turbine. One-dimensional (1D) Mean Line (ML) approach and three-dimensional computational fluid dynamic (3D CFD) simulations, using 3D Reynolds-Averaged Navier-Stokes (RANS) models with the shear stress transport (SST) turbulence model in ANSYS®15-CFX, were employed to achieve the best turbine performance and consequently cycle efficiency. For the current study, a new methodology that integrates the Brayton cycle analysis with modelling of a highly efficient small-scale radial turbine at a wide range of inlet temperatures was developed. A multi-objective function was utilized for optimizing the designed radial turbine power in the range of 1.5–7.5 kW. This method has been developed in order to find the optimum design, from an aerodynamic point of view. After applying a well-designed range of parameters for both the stator and the rotor, the results demonstrated an excellent improvement in the turbine efficiency from 82.3% to 89.7% for the same range of output power. Moreover, the effect of the turbine inlet temperature, rotational speed and pressure ratio was further studied and presented in this paper. Finally, the overall cycle efficiency showed an excellent improvement of about 6.5% for the current boundary conditions; and it yielded more than 10% with the increase in the inlet temperature and the pressure ratio. Such results highlight the potential and the benefits of the suggested methodology to achieve a high performance (i.e. turbine efficiency and cycle efficiency).

[1]  Emilie Sauret,et al.  Three-dimensional off-design numerical analysis of an organic Rankine cycle radial-inflow turbine , 2014 .

[2]  David Gordon Wilson,et al.  The design of high-efficiency turbomachinery and gas turbines , 1984 .

[3]  Josua P. Meyer,et al.  Operating conditions of an open and direct solar thermal Brayton cycle with optimised cavity receive , 2011 .

[4]  Murat Erbas,et al.  Design of low temperature Organic Rankine Cycle and turbine , 2013, 4th International Conference on Power Engineering, Energy and Electrical Drives.

[5]  K. Hooman,et al.  CFD simulation and FE analysis of a high pressure ratio radial inflow turbine , 2014 .

[6]  Raya Al-Dadah,et al.  One-Dimensional and Three-Dimensional Numerical Optimization and Comparison of Single-Stage Supersonic and Dual-Stage Transonic Radial Inflow Turbines for the ORC , 2016 .

[7]  Dieter Peitsch,et al.  Validation and Development of Loss Models for Small Size Radial Turbines , 2010 .

[8]  Yuting Wu,et al.  Dynamic Simulation of Closed Brayton Cycle Solar Thermal Power System , 2004 .

[9]  Josua P. Meyer,et al.  The efficiency of an open-cavity tubular solar receiver for a small-scale solar thermal Brayton cycle , 2014 .

[10]  A. Whitfield,et al.  Design of radial turbomachines , 1990 .

[11]  Noor A. Ahmed,et al.  Effect of the Ratio of Specific Heats on a Small Scale Solar Brayton Cycle , 2012 .

[12]  Qiang Zhang,et al.  Multiple-objective aerodynamic optimization design of a radial air turbine impeller , 2011, 2011 International Conference on Remote Sensing, Environment and Transportation Engineering.

[13]  Anthony C. Jones.  Design and Test of a Small, High Pressure Ratio Radial Turbine , 1994 .

[14]  Raya Al-Dadah,et al.  Modelling and optimization of organic Rankine cycle based on a small-scale radial inflow turbine , 2015 .

[15]  Josua P. Meyer,et al.  Optimum performance of the small-scale open and direct solar thermal Brayton cycle at various environmental conditions and constraints☆ , 2012 .

[16]  Emilie Sauret,et al.  Open design of high pressure ratio radial-inflow turbine for academic validation , 2012 .

[17]  H. E. Rohlik.  Analytical determination of radial inflow turbine design geometry for maximum efficiency , 1968 .

[18]  C. Cho,et al.  A Study of Cycle Analysis and Turbine Design for Obtaining Small-Scaled Power from the Organic Rankine Cycle Using R245fa , 2013 .

[19]  Ronald H. Aungier,et al.  Turbine Aerodynamics: Axial-Flow and Radial-Flow Turbine Design and Analysis , 2006 .

[20]  Kwang-Yong Kim,et al.  Performance enhancement of axial fan blade through multi-objective optimization techniques , 2010 .

[21]  Adrian Bejan,et al.  Entropy generation minimization in parallel‐plates counterflow heat exchangers , 2000 .

[22]  Peter Collings,et al.  Modelling and Analysis of a Small-Scale Organic Rankine Cycle System with a Scroll Expander , 2014 .

[23]  N. C. Baines,et al.  The aerodynamic loading of radial and mixed-flow turbines , 1994 .

[24]  Andrea Lazzaretto,et al.  New efficiency charts for the optimum design of axial flow turbines for organic Rankine cycles , 2014 .

[25]  Vincent Lemort,et al.  Design and Experimental investigation of a Small scale organic Rankine using a scroll expander , 2010 .

[26]  S. L. Dixon,et al.  Fluid mechanics, thermodynamics of turbomachinery , 1966 .

[27]  Rene Pecnik,et al.  Performance improvement of a radial organic Rankine cycle turbine by means of automated computational fluid dynamic design , 2013 .

[28]  Yan Shi,et al.  Integrated Optimization Design for a Radial Turbine Wheel of a 100 kW-Class Microturbine , 2012 .

[29]  Daniele Fiaschi,et al.  Thermo-fluid dynamics preliminary design of turbo-expanders for ORC cycles , 2012 .

[30]  Raya Al-Dadah,et al.  Parametric analysis and optimization of a small-scale radial turbine for Organic Rankine Cycle , 2015 .

[31]  Raya Al-Dadah,et al.  Minimization of loss in small scale axial air turbine using CFD modeling and evolutionary algorithm optimization , 2016 .

[32]  O. E. Baljé,et al.  Turbomachines—A Guide to Design Selection and Theory , 1981 .

[33]  Antonio Giuffrida,et al.  Modelling the performance of a scroll expander for small organic Rankine cycles when changing the working fluid , 2014 .

[34]  Tom Verstraete,et al.  Multidisciplinary Optimization of a Turbocharger Radial Turbine , 2012 .

[35]  Bum-Seog Choi,et al.  Development of a 200 kW ORC radial turbine for waste heat recovery , 2014 .

[36]  J. E. Haas,et al.  Experimental performance and analysis of 15.04-centimeter-tip-diameter, radial-inflow turbine with work factor of 1.126 and thick blading , 1980 .