Numerical Model of a Non-Contact Piezoelectric Energy Harvester for Rotating Objects

Energy harvesting is an attractive technique for powering wireless sensors and low power devices. Harvesters delivering sufficient power from rotation for sensor applications have been developed, but difficulties are encountered when the devices to be powered are located off-axis on a rotating object. In such cases, harvesters are not adapted to low frequency and high amplitude of motion, where the input force amplitude is higher than the mass available displacement. A novel approach, based on using non-contact piezoelectric energy harvester to generate power from magnetic forces due to the effect of the centripetal force is proposed in this paper. In this approach, the pre-stressed piezoelectric beams are deformed by interaction with an oscillating magnet that is supported by magnetic levitation system. Because the magnetic levitation system is nonlinear, the nonlinear spring enables operation over a wide range of large centripetal accelerations. A model of the system is presented and analyzed in order to identify the parameters that control the performance of the harvester. Theoretical investigations are followed by a series of experimental tests to validate the response predictions. With an off-axis distance of 75 mm the prototype, occupying a volume of approximately 17.74 cm3 and weighting 46 g, generated an output power ranging from 0.2 μW to 3.5 μW when the rotating speed changes from 3 rps to 5.55 rps. Further optimization of the piezoelectric harvester is carried out in order to improve the power density. An application in which the harvester can be used in is tire pressure monitoring systems. In this case, the harvester can replace the battery of the pressure sensors located inside the vehicle tire.

[1]  Jan M. Rabaey,et al.  Energy scavenging for wireless sensor networks , 2003 .

[2]  Eric M. Yeatman,et al.  Energy harvesting from motion using rotating and gyroscopic proof masses , 2008 .

[3]  M. Loehndorf,et al.  EVALUATION OF ENERGY HARVESTING CONCEPTS FOR TIRE PRESSURE MONITORING SYSTEMS , 2009 .

[4]  Eric M. Yeatman,et al.  A continuously rotating energy harvester with maximum power point tracking , 2008 .

[5]  Yiannos Manoli,et al.  Non-resonant vibration conversion , 2006 .

[6]  Patricia Morreale,et al.  Wireless Sensor Network Applications in Urban Telehealth , 2007, 21st International Conference on Advanced Information Networking and Applications Workshops (AINAW'07).

[7]  S. Farritor,et al.  On low-frequency electric power generation with PZT ceramics , 2005, IEEE/ASME Transactions on Mechatronics.

[8]  David P. Arnold,et al.  A study of scaling and geometry effects on the forces between cuboidal and cylindrical magnets using analytical force solutions , 2008 .

[9]  N. M. White,et al.  Harvesting energy from vehicle wheels , 2009, TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference.

[10]  M. Keck.  A new approach of a piezoelectric vibration-based power generator to supply next generation tire sensor systems , 2007, 2007 IEEE Sensors.

[11]  Guomao Yang,et al.  Uniaxial stress dependence of the piezoelectric properties of lead zirconate titanate ceramics , 2000, ISAF 2000. Proceedings of the 2000 12th IEEE International Symposium on Applications of Ferroelectrics (IEEE Cat. No.00CH37076).

[12]  S. P. Beeby,et al.  Experimental comparison of macro and micro scale electromagnetic vibration powered generators , 2007 .

[13]  Karla Mossi,et al.  Characterization of different types of high-performance THUNDER actuators , 1999, Smart Structures.

[14]  G. Akoun,et al.  3D analytical calculation of the forces exerted between two cuboidal magnets , 1984 .

[15]  M. Umeda,et al.  Analysis of the Transformation of Mechanical Impact Energy to Electric Energy Using Piezoelectric Vibrator , 1996 .

[16]  Shad Roundy,et al.  ENERGY HARVESTING FOR TIRE PRESSURE MONITORING SYSTEMS: DESIGN CONSIDERATIONS , 2008 .