Choked cavitation in micro-orifices: An experimental study

Abstract Choked cavitation was experimentally investigated with three circular micro-orifices with diameters of 150 μm and 300 μm and thicknesses of 1.04 mm, 1.06 mm and 1.93 mm. Water was used as the test fluid, and experiments were carried out with upstream pressures in the range of 5.1–13.5 MPa. The cavitation number at the inception and cessation of choked cavitation was found to increase with increasing the micro-orifice diameter and thickness. This suggests that micro-orifices could be characterized by very small choked cavitation numbers and therefore might be less susceptible to choking than their macro-scale counterparts. The cavitation number at the inception and cessation of choked cavitation was independent of the upstream pressure, downstream pressure, average flow velocity and orifice Reynolds number. At choking, the ratio of the upstream pressure to the downstream pressure is constant for a given micro-orifice, while during choked flow the mass flow rate through the micro-orifice is proportional to the square root of the upstream pressure.

[1]  Jesus Rodriguez-Manzano,et al.  Digital biology and chemistry. , 2014, Lab on a chip.

[2]  Ali Koşar,et al.  Cavitation Enhanced Heat Transfer in Microchannels , 2006 .

[3]  S. Wongwises,et al.  A review of numerical modelling studies on short-tube orifice performance with applications to air-conditioning systems , 2012 .

[4]  Manolis Gavaises,et al.  Instantaneous and ensemble average cavitation structures in Diesel micro-channel flow orifices , 2014 .

[5]  Somchai Wongwises,et al.  Review on the experimental studies of refrigerant flow mechanisms inside short-tube orifices , 2012 .

[6]  K. Ramamurthi,et al.  Characteristics of flow through small sharp-edged cylindrical orifices , 1999 .

[7]  J. Thome,et al.  Fine-resolution two-phase flow heat transfer coefficient measurements of refrigerants in multi-microchannel evaporators , 2013 .

[8]  Yoav Peles,et al.  Flow visualization of cavitating flows through a rectangular slot micro-orifice ingrained in a microchannel , 2005 .

[9]  Predrag Stojan Hrnjak,et al.  Refrigerant 134a liquid flow through micro-scale short tube orifices with/without phase change , 2006 .

[10]  Juan G. Santiago,et al.  A review of micropumps , 2004 .

[11]  Somchai Wongwises,et al.  Choked flow mechanism of HFC-134a flowing through short-tube orifices , 2011 .

[12]  Ibrahim Hassan,et al.  MICROCHANNEL HEAT SINKS: AN OVERVIEW OF THE STATE-OF-THE-ART , 2004 .

[13]  Jong Min Choi,et al.  A generalized correlation for two-phase flow of alternative refrigerants through short tube orifices. , 2004 .

[14]  J. Fröhlich,et al.  Optical measurements of gas bubbles in oil behind a cavitating micro-orifice flow , 2015 .

[15]  Jaap C. Schouten,et al.  Hydrodynamic cavitation in micro channels with channel sizes of 100 and 750 micrometers , 2012 .

[16]  A. Ushida,et al.  Anomalous phenomena in pressure drops of water flows through micro-orifices , 2014 .

[17]  Dennis L. O'Neal,et al.  A semi-empirical model of two-phase flow of refrigerant-134a through short tube orifices , 1994 .

[18]  J. Taylor.  An Introduction to Error Analysis , 1982 .

[19]  N. Stevens,et al.  Investigation of the role of electrokinetic effects in corrosion deposit formation , 2014 .

[20]  Y. M. Niu,et al.  Experimentation and correlation of R744 two-phase flow through short tubes , 2004 .

[21]  Rex B. Thorpe,et al.  Flow regime transitions due to cavitation in the flow through an orifice , 1990 .

[22]  A. Ushida,et al.  Anomalous phenomena in several types of liquid flows through small orifices in a range of low Reynolds numbers , 2014 .

[23]  M. Gad-el-Hak.  The Fluid Mechanics of Microdevices—The Freeman Scholar Lecture , 1999 .

[25]  S. Wongwises,et al.  Flow mechanisms of HFC-410A inside short-tube orifices during flashing process , 2010 .

[26]  Y. Peles,et al.  The effects of fluid properties on cavitation in a micro domain , 2009 .

[27]  A. Cioncolini,et al.  Micro-orifice single-phase liquid flow: Pressure drop measurements and prediction , 2015 .

[28]  S. Wongwises,et al.  Flow pattern, mass flow rate, pressure distribution, and temperature distribution of two-phase flow of HFC-134a inside short-tube orifices , 2009 .

[29]  S. D. Senturia,et al.  Macro Power from Micro Machinery , 1997, Science.

[30]  C. Tien,et al.  Recent developments in microscale thermophysical engineering , 1999 .

[31]  R. Shah,et al.  Fluid Flow and Heat Transfer at Micro- and Meso-Scales With Application to Heat Exchanger Design , 2000 .

[32]  Yoav Peles,et al.  Cavitation in flow through a micro-orifice inside a silicon microchannel , 2005 .

[33]  S. Lyon,et al.  Stress corrosion cracking of Ru doped 304 stainless steel in high temperature water , 2012 .

[34]  Kristen L. Helton,et al.  Microfluidic Overview of Global Health Issues Microfluidic Diagnostic Technologies for Global Public Health , 2006 .

[35]  Tomiichi Hasegawa,et al.  Anomaly of excess pressure drops of the flow through very small orifices , 1997 .

[36]  Chih-Ming Ho,et al.  REVIEW: MEMS and Its Applications for Flow Control , 1996 .

[37]  S. Lyon,et al.  Influence of Pd and Ru additions on stress corrosion cracking of austenitic stainless steels , 2012 .

[38]  Nam-Trung Nguyen,et al.  Micromixers?a review , 2005 .