Prediction of Reponses in a Sustainable Dry Turning Operation: A Comparative Analysis
暂无分享,去创建一个
Prasenjit Chatterjee | Shankar Chakraborty | Shibaprasad Bhattacharya | Partha Protim Das | S. Chakraborty | Prasenjit Chatterjee | Shibaprasad Bhattacharya | Partha Protim Das
[1] Uday S. Dixit,et al. Environmentally Friendly Machining , 2012 .
[2] S. Chakraborty,et al. Grey-fuzzy method-based parametric analysis of abrasive water jet machining on GFRP composites , 2020 .
[3] I. Panigrahi,et al. Prediction models for on-line cutting tool and machined surface condition monitoring during hard turning considering vibration signal , 2020, Mechanics & Industry.
[4] Asif Ali Laghari,et al. A Review on Application of Soft Computing Techniques in Machining of Particle Reinforcement Metal Matrix Composites , 2019, Archives of Computational Methods in Engineering.
[5] S. Chakraborty,et al. Fuzzy modeling and parametric analysis of non-traditional machining processes , 2023, Management and Production Engineering Review.
[6] H. Aouici,et al. Design optimization of cutting parameters when turning hardened AISI H11 steel (50 HRC) with CBN7020 tools , 2017 .
[7] Patrick van der Smagt,et al. Introduction to neural networks , 1995, The Lancet.
[8] Mourad Nouioua,et al. Comparative assessment of machining environments (dry, wet and MQL) in hard turning of AISI 4140 steel with CC6050 tools , 2019, The International Journal of Advanced Manufacturing Technology.
[9] S. Chauhan,et al. Comparative Analysis and Optimization of FEM and RSM Based Regression Model with Experimental Results for the Dry Turning of SiCp- Al7075 Composite , 2020, Silicon.
[10] A. Almeshal,et al. Prediction and Optimization of Surface Roughness in a Turning Process Using the ANFIS-QPSO Method , 2020, Materials.
[11] S. K. Rajbongshi,et al. A comparative study in prediction of surface roughness and flank wear using artificial neural network and response surface methodology method during hard turning in dry and forced air-cooling condition , 2019, International Journal of Machining and Machinability of Materials.
[12] Davorin Kramar,et al. Predictive modeling of turning operations under different cooling/lubricating conditions for sustainable manufacturing with machine learning techniques , 2020, Applied Computing and Informatics.
[13] Jan-Eric Ståhl,et al. Sustainable machining through increasing the cutting tool utilization , 2013 .
[14] Robert LIN,et al. NOTE ON FUZZY SETS , 2014 .
[15] Ali M. Abdulshahed,et al. Prediction and control of surface roughness for end milling process using ANFIS , 2019 .
[16] R. Stephenson. A and V , 1962, The British journal of ophthalmology.
[17] Lotfi A. Zadeh,et al. Fuzzy Sets , 1996, Inf. Control..
[18] Sami Ekici,et al. An adaptive neuro-fuzzy inference system (ANFIS) model for wire-EDM , 2009, Expert Syst. Appl..
[19] Jyh-Shing Roger Jang,et al. ANFIS: adaptive-network-based fuzzy inference system , 1993, IEEE Trans. Syst. Man Cybern..
[20] Mozammel Mia,et al. Effects of cutting parameters and machining environments on surface roughness in hard turning using design of experiment , 2016 .
[21] Yvonne Koch,et al. Environmentally Friendly Machining , 2016 .
[22] Amlana Panda,et al. Tool condition monitoring during hard turning of AISI 52100 Steel: A case study , 2018 .
[23] M. Yallese,et al. Comparison on various machinability aspects between mixed and reinforced ceramics when machining hardened steels , 2019, Mechanics & Industry.
[24] Shankar Chakraborty,et al. Application of grey-fuzzy logic technique for parametric optimization of non-traditional machining processes , 2017, Grey Syst. Theory Appl..
[25] M. Koura,et al. Modeling and Prediction of Surface Roughness During Dry Turning Process , 2014 .
[26] Reza Teimouri,et al. Application of Taguchi, ANFIS and grey relational analysis for studying, modeling and optimization of wire EDM process while using gaseous media , 2014 .
[27] Zoran Jurković,et al. OPTIMIZATION OF TURNING PROCESS , 2017 .
[28] S. Gangopadhyay,et al. Multi-objective Optimization of Machining Parameters During Dry Turning of AISI 304 Austenitic Stainless Steel Using Grey Relational Analysis , 2014 .