Impact modeling of foam cored sandwich plates with ductile or brittle faceplates

Abstract This paper reports numerical results of low velocity impact on open-face sandwich plates with an impactor of 2.65 kg mass hitting with 6.7 m/s velocity. The numerical simulation is done using 3D finite element models in LS-DYNA. The sandwich plates used for the present work have a core made of commercial aluminum alloy foam (Alporas) with faceplates made of either ductile aluminum (Al) or brittle carbon fiber reinforced plastic (CFRP). Selection of suitable constitutive models and erosion criterion for the failure analysis is investigated. A simplified analytical model for the peak load prediction under punch-through failure mode is presented. Numerically predicted contact force versus time, energy absorbed versus time along with the failure modes are compared with the experimental measurements and observations. Within experimental scatter, there is a good agreement between the numerical predictions and experimental measurements. Further more, the analytically predicted peak load values are in excellent agreement with the experimental measurements.

[1]  Michelle S. Hoo Fatt,et al.  Dynamic models for low-velocity impact damage of composite sandwich panels – Part B: Damage initiation , 2001 .

[2]  Anthony N. Palazotto,et al.  Low-velocity impact damage initiation in graphite/epoxy/Nomex honeycomb-sandwich plates , 1998 .

[3]  Robin Olsson,et al.  Engineering Method for Prediction of Impact Response and Damage in Sandwich Panels , 2002 .

[4]  Gin Boay Chai,et al.  Low-velocity impact failure of aluminium honeycomb sandwich panels , 2008 .

[5]  N. El-Abbasi,et al.  FE modelling of deformation localization in metallic foams , 2002 .

[6]  O. Hopperstad,et al.  Constitutive modeling of aluminum foam including fracture and statistical variation of density , 2003 .

[7]  L. S. Ong,et al.  Dynamic indentation and penetration of aluminium foams , 2008 .

[8]  Lorna J. Gibson,et al.  Failure of aluminum foams under multiaxial loads , 2000 .

[9]  M. Ashby,et al.  Cellular solids: Structure & properties , 1988 .

[10]  Norman A. Fleck,et al.  The multiaxial yield behaviour of an aluminium alloy foam , 2005 .

[11]  M. Ashby,et al.  Indentation resistance of an aluminium foam , 2000 .

[12]  M. Alkhader,et al.  An energy-based anisotropic yield criterion for cellular solids and validation by biaxial FE simulations , 2009 .

[13]  Ronald E. Miller.  A continuum plasticity model for the constitutive and indentation behaviour of foamed metals , 2000 .

[14]  M. Ashby,et al.  Metal Foams: A Design Guide , 2000 .

[15]  C. Santiuste,et al.  FEM analysis of dynamic flexural behaviour of composite sandwich beams with foam core , 2010 .

[16]  Reinhard Pippan,et al.  DEFORMATION BEHAVIOUR OF CLOSED-CELL ALUMINIUM FOAMS IN TENSION , 2001 .

[17]  N. Fleck,et al.  Isotropic constitutive models for metallic foams , 2000 .

[18]  Masaki Omiya,et al.  Compressive Deformation in Aluminum Foam Investigated Using a 2D Object Oriented Finite Element Modeling Approach , 2007 .

[19]  Isaac M Daniel,et al.  Low velocity impact behavior of composite sandwich panels , 2005 .

[20]  K. Malekzadeh,et al.  Response of composite sandwich panels with transversely flexible core to low-velocity transverse impact: A new dynamic model , 2007 .

[21]  O. Hopperstad,et al.  Validation of constitutive models applicable to aluminium foams , 2002 .

[22]  S. Sanchez-Saez,et al.  Numerical modelling of foam-cored sandwich plates under high-velocity impact , 2011 .