Advanced Thermal-Hydraulic experiments and instrumentation for heavy liquid metal reactors

[1]  S. Eckert,et al.  Contactless Inductive Flow Tomography for Real-Time Control of Electromagnetic Actuators in Metal Casting , 2022, Sensors.

[2]  Flow reconstruction in a Rayleigh-Bénard convection cell with an aspect ratio 0.5 by contactless inductive flow tomography , 2022, Magnetohydrodynamics.

[3]  T. Sasa,et al.  Development of a miniature electromagnet probe for the measurement of local velocity in heavy liquid metals , 2022, Journal of Nuclear Science and Technology.

[4]  I. Muttakin,et al.  Laboratory Investigation of Tomography-Controlled Continuous Steel Casting , 2022, Sensors.

[5]  T. Schaub,et al.  Design and calibration of permanent magnet probes for the local measurement of velocity and temperature in a liquid metal backward facing step flow , 2021, Experiments in Fluids.

[6]  D. Castelliti,et al.  Total loss of flow benchmark in CIRCE-HERO integral test facility , 2021 .

[7]  G. Gerbeth,et al.  Eddy Current Flow Meter Performance in Liquid Metal Flows Inclined to the Sensor Axis , 2021 .

[8]  Mariano Tarantino,et al.  Simulation of operational conditions of HX-HERO in the CIRCE facility with CFD/STH coupled codes , 2020 .

[9]  F. J. Ruiz-Cabañas,et al.  Carbonate molten salt solar thermal pilot facility: Plant design, commissioning and operation up to 700 °C , 2020 .

[10]  M. Tarantino,et al.  Post-test simulation of a PLOFA transient test in the CIRCE-HERO facility , 2019, Nuclear Engineering and Design.

[11]  M. Tarantino,et al.  Blockage fuel pin simulator experiments and simulation , 2019, Nuclear Engineering and Design.

[12]  T. Wetzel,et al.  Experimental study of the influence of inter-wrapper flow on liquid-metal cooled fuel assemblies , 2019, Nuclear Engineering and Design.

[13]  N. Forgione,et al.  Experimental analysis of stationary and transient scenarios of alfred steam generator bayonet tube in circe-hero facility , 2019, Nuclear Engineering and Design.

[14]  S. K. Chen,et al.  The upgraded Cheng and Todreas correlation for pressure drop in hexagonal wire-wrapped rod bundles , 2018 .

[15]  Hitoshi Asano,et al.  Applicability of hybrid ultrasonic flow meter for wide-range flow-rate under distorted velocity profile conditions , 2018, Experimental Thermal and Fluid Science.

[16]  Daniele Martelli,et al.  Experimental campaign on the HLM loop NACIE-UP with instrumented wire-spaced fuel pin simulator , 2018, Nuclear Engineering and Design.

[17]  Fabio Giannetti,et al.  GEN-IV LFR development: Status & perspectives , 2018 .

[18]  T. Wetzel,et al.  Heat transfer experiment in a partially (internally) blocked 19-rod bundle with wire spacers cooled by LBE , 2018 .

[19]  T. Wondrak,et al.  Measurement techniques for liquid metals , 2017 .

[20]  J. Priede,et al.  Alternative transient eddy-current flowmetering methods for liquid metals , 2017, Flow Measurement and Instrumentation.

[21]  Sven Eckert,et al.  Visualization of the global flow structure in a modified Rayleigh-Bénard setup using contactless inductive flow tomography , 2017, Flow Measurement and Instrumentation.

[22]  T. Wetzel,et al.  Experimental study of heavy-liquid metal (LBE) flow and heat transfer along a hexagonal 19-rod bundle with wire spacers , 2016 .

[23]  Mariano Tarantino,et al.  Heat transfer on HLM cooled wire-spaced fuel pin bundle simulator in the NACIE-UP facility , 2016 .

[24]  Katrien Van Tichelen,et al.  E-SCAPE: A scale facility for liquid-metal, pool-type reactor thermal hydraulic investigations , 2015 .

[25]  F. Stefani,et al.  Transient eddy current flow metering , 2015, 1505.05959.

[26]  Andreas G. Class,et al.  Integral Circulation Experiment: Thermal–hydraulic simulator of a heavy liquid metal reactor , 2011 .

[27]  Gunter Gerbeth,et al.  Contactless electromagnetic phase-shift flowmeter for liquid metals , 2010, 1010.0404.

[28]  Konstantin Mikityuk,et al.  Heat transfer to liquid metal: Review of data and correlations for tube bundles , 2009 .

[29]  G. Gerbeth,et al.  Contactless inductive flow tomography. , 2004, Physical review. E, Statistical, nonlinear, and soft matter physics.

[30]  J. W. Evans,et al.  Toward a probe for velocity measurement in molten metals at high temperatures , 1999 .

[31]  M. Iguchi,et al.  Bubble and liquid flow characteristics in a wood’s metal bath stirred by bottom helium gas injection , 1997 .

[32]  Thomas von Weissenfluh,et al.  Probes for local velocity and temperature measurements in liquid metal flow , 1985 .

[33]  I. Platnieks,et al.  Hot-wire sensor for liquid sodium , 1984 .

[34]  Charles Vives,et al.  Local velocity and mass transfer measurements in molten metals using an incorporated magnet probe , 1982 .

[35]  M. Kazimi,et al.  Clinch River Breeder Reactor Plant. Heat transfer correlation for analysis of CRBRP assemblies , 1976 .

[36]  C. Sleicher,et al.  Directional Sensitivity of Hot Film Sensors in Liquid Metals , 1971 .

[37]  Aleksander Wosniok,et al.  Distributed Brillouin Sensing: Frequency-Domain Techniques , 2019, Handbook of Optical Fibers.

[38]  F. Stefani,et al.  Immersed transient eddy current flow metering: a calibration-free velocity measurement technique for liquid metals , 2017 .

[39]  Yasushi Takeda,et al.  Ultrasonic Doppler Velocity Profiler for Fluid Flow , 2012 .

[40]  K. Rehme.  Pressure Drop Correlations for Fuel Element Spacers , 1973 .