Residual strain development in an AS4/PPS thermoplastic composite measured using fibre Bragg grating sensors

Abstract This paper demonstrates the use of fibre Bragg grating (FBG) sensors for the measurement of residual strain development during the consolidation of a thermoplastic composite. During the processing of the carbon fibre-reinforced polyphenylene sulphide (AS4/PPS) laminate, FBG sensors respond to changes in material state, for example the glass-rubber transition and solid–liquid transition. The sensors also permit the observation of wavelength shifts and spectral form changes induced by the contraction of the composite during cooling. The experimental data are compared to a generalized plane strain, thermoelastic numerical model with temperature dependent matrix dominated properties. The model provides solutions for two limiting cases: one where the specimen contracts freely, and one where the specimen is restricted by perfect contact with the mould. Strain values calculated in each case are inserted into optomechanical equations, which convert the strain state in the FBG to a corresponding change in wavelength. In this way, the modelled cases are compared to FBG wavelength shifts during consolidation.

[1]  José Manuel Menéndez,et al.  Bragg-grating-based multiaxial strain sensing: its application to residual strain measurement in composite laminates , 2000, Smart Structures.

[2]  J. A. Barnes,et al.  The formation of residual stresses in laminated thermoplastic composites , 1994 .

[3]  Craig M. Lawrence,et al.  Measurement of process-induced strains in composite materials using embedded fiber optic sensors , 1996 .

[4]  M. Dupont,et al.  Embedded Fiber Bragg Grating Sensors for Industrial Composite Cure Monitoring , 1998 .

[5]  Larissa K. Sorensen,et al.  Long FBG sensor characterization of residual strains in AS4/PPS thermoplastic laminates , 2004, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[6]  G.M. Williams,et al.  Hybrid fiber Bragg grating/long period fiber grating sensor for strain/temperature discrimination , 1996, IEEE Photonics Technology Letters.

[7]  M. Douay,et al.  Thermal hysteresis of Bragg wavelengths of intra-core fiber gratings , 1993, IEEE Photonics Technology Letters.

[8]  Nobuo Takeda,et al.  Effect of thermal residual stress on the reflection spectrum from fiber Bragg grating sensors embedded in CFRP laminates , 2002 .

[9]  G. Jeronimidis,et al.  Residual Stresses in Carbon Fibre-Thermoplastic Matrix Laminates , 1988 .

[10]  Maurice Whelan,et al.  Residual strain measurement and impact response of optical fibre Bragg grating sensors in fibre metal laminates , 2001 .

[11]  J. Sirkis.  Unified approach to phase-strain-temperature models for smart structure interferometric optical fiber sensors: part 1, development , 1993 .

[12]  C. Sun,et al.  Experimental Characterization of Constitutive Models for PEEK Thermoplastic Composite at Heating Stage during Forming , 1997 .

[13]  Joël Cugnoni,et al.  Inverse method based on modal analysis for characterizing the constitutive properties of thick composite plates , 2007 .

[14]  George S. Springer,et al.  Strain and Temperature Measurement with Fiber Optic Sensors , 1996 .

[15]  F. Sonmez,et al.  Optimal post-manufacturing cooling paths for thermoplastic composites , 2002 .

[16]  J. A. Guemes,et al.  Response of Bragg grating fiber-optic sensors when embedded in composite laminates , 2002 .

[17]  H. Kim,et al.  Performance improvement of glass fiber–poly(phenylene sulfide) composite , 1996 .