Finite element modeling of Lamb wave propagation in composite stepped joints

The objective of this research is to evaluate the integrity of a composite bonded joint by simulating Lamb wave propagation using finite element methods. The structure of interest is composed of two stepped carbon fiber reinforced polymer plates bonded together by an adhesive film. Two different bonding conditions are examined for the joint: undamaged and damaged (with disbond). In the finite element model, an antisymmetric guided wave is excited by imposing an out-of-plane displacement on the surfaces and a spatial Fourier transform is performed before and after the bond line for extraction of reflection and transmission coefficients. For validation, experiments are also conducted using two colocalized rectangular piezoceramics for plane wave generation. A 3D laser Doppler vibrometer is employed for noncontact measurement of the in-plane and out-of-plane velocity. The results confirm the reflections from the steps’ edges, and it is found that the level of reflection and transmission of the guided wave mode is different for undamaged and damaged joints. The antisymmetric mode in the pulse-echo configuration seems to be an efficient mode and strategy for disbond detection in composite repairs. The results verify that guided wave propagation is very effective for disbond detection in composite bonded joints and scarf repairs.

[1]  Lowe,et al.  The transmission of Lamb waves across adhesively bonded lap joints , 2000, The Journal of the Acoustical Society of America.

[2]  Mohammad H. Sherafat,et al.  Guided wave scattering behavior in composite bonded assemblies , 2016 .

[3]  Jing Jin,et al.  Wave boundary element to study Lamb wave propagation in plates , 2005 .

[4]  Krishnan Balasubramaniam,et al.  Interaction of guided Lamb waves with an asymmetrically located delamination in a laminated composite plate , 2010 .

[5]  Laurence J. Jacobs,et al.  Propagation of guided waves in adhesive bonded components , 2002 .

[6]  Peter Cawley,et al.  A 2-dimensional Fourier transform method for the quantitative measurement of Lamb modes , 1990, IEEE Symposium on Ultrasonics.

[7]  Usik Lee,et al.  Guided waves in a Timoshenko beam with a bonded composite patch: Frequency domain spectral element modeling and analysis , 2014 .

[8]  Ivan Bartoli,et al.  Ultrasonic guided wave monitoring of composite wing skin-to-spar bonded joints in aerospace structures , 2005 .

[9]  P. Cawley,et al.  The interaction of Lamb waves with delaminations in composite laminates , 1993 .

[10]  Youhong Tang,et al.  Monitoring of delamination onset and growth during Mode I and Mode II interlaminar fracture tests using guided waves , 2012 .

[11]  Lin Ye,et al.  Some aspects of numerical simulation for Lamb wave propagation in composite laminates , 2006 .

[12]  C Soutis,et al.  Design and performance of bonded patch repairs of composite structures , 1997 .

[13]  Junji Takatsubo,et al.  IMPACT DAMAGE DETECTION ON SCARF-REPAIRED COMPOSITES USING LAMB WAVE SENSING , 2007 .

[14]  Mohammad H. Sherafat,et al.  Structural health monitoring of a composite skin-stringer assembly using within-the-bond strategy of guided wave propagation , 2016 .

[15]  Nezih Mrad,et al.  Broadband generation of ultrasonic guided waves using piezoceramics and sub-band decomposition , 2012, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[16]  Marcias Martinez,et al.  Structural health monitoring of bonded composite repairs – A critical comparison between ultrasonic Lamb wave approach and surface mounted crack sensor approach , 2013 .

[17]  Z. Su,et al.  Identification of Damage Using Lamb Waves , 2009 .

[18]  Chun-Gon Kim,et al.  The propagation of Lamb waves in a laminated composite plate with a variable stepped thickness , 2006 .

[19]  Patrice Masson,et al.  Guided Wave Propagation through Composite Bonded Joints , 2014 .

[20]  N. D. Boffa,et al.  Ultrasonic wave propagation in composite laminates by numerical simulation , 2015 .

[21]  K. Balasubramaniam,et al.  Interaction of the primary anti-symmetric Lamb mode (Ao) with symmetric delaminations: numerical and experimental studies , 2009 .

[22]  Younho Cho,et al.  A boundary element solution for a mode conversion study on the edge reflection of Lamb waves , 1996 .

[23]  Markus G. R. Sause,et al.  Finite element modeling of lamb wave propagation in anisotropic hybrid materials , 2013 .

[24]  Prabhu Rajagopal,et al.  An approach for defect visualization and identification in composite plate structures using air-coupled guided ultrasound , 2015 .

[25]  Patrice Masson,et al.  Assessment of the excitelet algorithm for in-situ mechanical characterization of orthotropic structures , 2012, Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[26]  Pierre-Claude Ostiguy,et al.  Selection of structural features for the systematic study of guided wave propagation and interaction with damage , 2015 .

[27]  W. Staszewski,et al.  Modelling of Lamb waves for damage detection in metallic structures: Part II. Wave interactions with damage , 2003 .

[28]  Takahiro Hayashi,et al.  Multiple reflections of Lamb waves at a delamination. , 2002, Ultrasonics.

[29]  Francesco Lanza di Scalea,et al.  Propagation of ultrasonic guided waves in lap-shear adhesive joints: case of incident a0 Lamb wave. , 2004 .

[30]  Pd Wilcox,et al.  Modeling the Excitation of Lamb and SH Waves by Point and Line Sources , 2004 .

[31]  Wieslaw Ostachowicz,et al.  Damage detection of structures using spectral finite element method , 2008 .

[32]  Philippe Micheau,et al.  Methodology for optimal configuration in structural health monitoring of composite bonded joints , 2012 .