High Shock-Resistant Design for Wafer-Level-Packaged Three-Axis Accelerometer With Ring-Shaped Beam

A novel high shock-resistant beam design for a piezoresistive three-axis accelerometer with a distinctive ring-shaped beam structure introduced for relaxing assembling stresses is discussed. Through simulations modeling shock tests, the transient responses of a sensor device having a mass suspended with four beams and encapsulated using a wafer-level-packaging process were analyzed in detail. The beams are negatively affected by large axial tensile stress originating from a high-frequency vibration mode, and rapid stress increases just after the crashing of the mass into the encapsulation caps. Thus, the ring beam should be designed to simultaneously reduce the maximum stress for shock resistance and increase flexibility for stress relaxation against axial tensile load. A noticeable shock resistance against a peak acceleration of 20 000 G was achieved without sacrificing the stress-relaxation effect of the ring by applying an optimized ring design and minimizing the gap between the mass and cap to soften the crash. [2017-0237]

[1]  Jian Dong,et al.  Silicon micromachined high-shock accelerometers with a curved-surface-application structure for over-range stop protection and free-mode-resonance depression , 2002 .

[2]  V. T. Srikar,et al.  The reliability of microelectromechanical systems (MEMS) in shock environments , 2002 .

[3]  M. Esashi,et al.  Wafer level packaging of MEMS , 2008, TRANSDUCERS 2009 - 2009 International Solid-State Sensors, Actuators and Microsystems Conference.

[4]  M. Younis,et al.  The response of clamped–clamped microbeams under mechanical shock , 2007 .

[5]  A. Tseng,et al.  Low stress packaging of a micromachined accelerometer , 2001 .

[6]  A. Kazama,et al.  Stress Relaxation Mechanism With a Ring-Shaped Beam for a Piezoresistive Three-Axis Accelerometer , 2013, Journal of Microelectromechanical Systems.

[7]  Oliver Paul,et al.  Mechanical Reliability of MEMS-structures under shock load , 2001, Microelectron. Reliab..

[8]  Sang Won Yoon,et al.  Shock-Protection Improvement Using Integrated Novel Shock-Protection Technologies , 2011, Journal of Microelectromechanical Systems.

[9]  MEMS Wafer-Level Packaging with Conductive Vias and Wafer Bonding , 2007, TRANSDUCERS 2007 - 2007 International Solid-State Sensors, Actuators and Microsystems Conference.

[10]  Xin Zhang,et al.  Accurate Assessment of Packaging Stress Effects on MEMS Sensors by Measurement and Sensor–Package Interaction Simulations , 2007, Journal of Microelectromechanical Systems.

[11]  N. Hablutzel,et al.  Low-cost packaging of inertial MEMS devices , 2003 .

[12]  W. Fang,et al.  A novel stress isolation guard-ring design for the improvement of a three-axis piezoresistive accelerometer , 2011 .

[13]  Jaume Esteve,et al.  Twin-mass accelerometer optimization to reduce the package stresses , 2000 .

[15]  M. Schmidt.  Wafer-to-wafer bonding for microstructure formation , 1998, Proc. IEEE.

[16]  K. Najafi,et al.  Vacuum packaging technology using localized aluminum/silicon-to-glass bonding , 2002, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[17]  V Narasimhan,et al.  Micromachined high-g accelerometers: a review , 2015 .

[18]  Thomas W. Kenny,et al.  An Integrated Wafer-Scale Packaging Process for MEMS , 2002 .

[19]  K. Okada.  Tri-Axial Piezoresistive Accelerometer , 1992 .

[20]  L. B. Wilner.  A high performance variable capacitance accelerometer , 1988, 1988. IMTC-88. 5th IEEE Instrumentation and Measurement Technology Conference.

[21]  Benedetto Vigna.  MEMS Epiphany , 2009, 2009 IEEE 22nd International Conference on Micro Electro Mechanical Systems.

[22]  J. T. Suminto,et al.  A wide frequency range, rugged silicon micro accelerometer with overrange stops , 1996, Proceedings of Ninth International Workshop on Micro Electromechanical Systems.