Sliding velocity dependency of the friction coefficient of Si-containing diamond-like carbon film under oil lubricated condition

Abstract In this study we investigated the sliding velocity dependency of the coefficient of friction for a Si-containing diamond-like carbon (DLC-Si) film in an automatic transmission fluid (ATF) under a wide range of contact pressures. The DLC-Si film and a nitrided steel with a surface roughness, R z JIS , of around 3.0 μm were used as disk specimens. A high-carbon chromium steel (JIS-SUJ2) bearing ball was used as a ball specimen. Friction tests were conducted using a ball-on-disk friction apparatus under a wide range of sliding velocites (0.1–2.0 m/s) and contact pressures ( P max : 0.42–3.61 GPa) in ATF. The friction coefficients for the nitrided steel had a tendency to decrease with an increase in sliding veloicity under all the contact pressure conditions; however, the friction coefficients for the DLC-Si film were stable with respect to sliding velocities under all the contatct pressures. These results indicate that the DLC-Si film suppresses the stick-slip motion during sliding againt steel in ATF, which is a desired frictional characteristic for the electromagnetic clutch disks used under lubrication. Furthermore, the DLC-Si film showed a higher wear resistance and lower aggression on the steel ball specimen than the nitrided steel. There were less hydrodynamic effects on the friction coefficient for the DLC-Si film possibly due to maintenance of the initial surface roughness and its poorer wettability with the fluid. X-ray photoelectron spectroscopy (XPS) analysis of the sliding surfaces revealed that the adsorption film derived from the succinimide on the sliding surfaces of the DLC-Si film and the mating steel ball also contributed to the sufficient and less sliding-velocity-dependant friction coefficients.

[1]  Fumio Ueda,et al.  Development of Automatic Transmission Fluid for Slip-Controlled Lock-Up Clutch Systems , 1995 .

[2]  O. Vinogradova.  Slippage of water over hydrophobic surfaces , 1999 .

[3]  Jože Vižintin,et al.  The Stribeck curve and lubrication design for non-fully wetted surfaces , 2009 .

[4]  M. Kalin,et al.  The influence of viscosity on the friction in lubricated DLC contacts at various sliding velocities , 2009 .

[5]  K. Hokkirigawa,et al.  Tribological properties of Si-containing diamond-like carbon film under ATF lubricated condition , 2009 .

[6]  K. Oguri,et al.  Two different low friction mechanisms of diamond-like carbon with silicon coatings formed by plasma-assisted chemical vapor deposition , 1992 .

[7]  T. Tallián.  On Competing Failure Modes in Rolling Contact , 1967 .

[8]  H. Mori,et al.  Structural analysis of Si-containing diamond-like carbon , 2006 .

[9]  H. Mori,et al.  Increased adhesion of diamond-like carbon-Si coatings and its tribological properties , 2002 .

[10]  Fumio Ueda,et al.  Anti-shudder mechanism of ATF additives (part 2): Influence of boundary frictional property and contact area roughness , 2002 .

[11]  Olga I. Vinogradova,et al.  Drainage of a Thin Liquid Film Confined between Hydrophobic Surfaces , 1995 .

[12]  K. Oguri,et al.  Tribological properties and characterization of diamond-like carbon coatings with silicon prepared by plasma-assisted chemical vapour deposition , 1991 .

[13]  Hugh Spikes,et al.  Equation for Slip of Simple Liquids at Smooth Solid Surfaces , 2003 .

[14]  Fumio Ueda,et al.  Anti-shudder mechanism of ATF additives (part 1): Formation of contact area roughness , 2002 .

[15]  Takanori Kugimiya.  Effects of additives of ATF and components of friction material for AT on μ-v characteristics , 2000 .

[16]  Fumio Ueda,et al.  Next Generation High Performance ATF for Slip-Controlled Automatic Transmission , 1997 .

[17]  Steve Granick,et al.  No-slip boundary condition switches to partial slip when fluid contains surfactant , 2002 .