Quenching chatter instability in turning process with a vibro-impact nonlinear energy sink

Abstract This paper investigates the passive control of chatter instability in turning processes using a vibro-impact nonlinear energy sink (NES). The workpiece is assumed to be rigid and the tool is flexible. A dynamical model including a nonlinear cutting law is presented and the stability lobes diagram is obtained. The behavior of the system with the vibro-impact NES is investigated using an asymptotic analysis. A control mechanism by successive beating is revealed, similarly to the strongly modulated response in the case of NES with cubic stiffness. It is shown that such a response regime may be beneficial for chatter mitigation. An original experimental procedure is proposed to verify the sizing of the vibro-impact NES. An experimental setup is developed with a vibro-impact NES embedded on the lathe tool and the results are analyzed and validated.

[1]  Guilhem Michon,et al.  Experimental Investigation and Design Optimization of Targeted Energy Transfer Under Periodic Forcing , 2014 .

[2]  Stefano Lenci,et al.  Periodic solutions and bifurcations in an impact inverted pendulum under impulsive excitation , 2000 .

[3]  G. Litak,et al.  APPROXIMATE ANALYTICAL SOLUTIONS FOR PRIMARY CHATTER IN THE NON-LINEAR METAL CUTTING MODEL , 2003 .

[4]  J. H. Xie,et al.  Symmetry and bifurcations of a two-degree-of-freedom vibro-impact system , 2008 .

[5]  Marian Wiercigroch,et al.  Chaotic Vibration of a Simple Model of the Machine Tool-Cutting Process System , 1997 .

[6]  D. M. McFarland,et al.  Application of broadband nonlinear targeted energy transfers for seismic mitigation of a shear frame: Computational results , 2008 .

[7]  Oleg Gendelman,et al.  Energy Pumping in Nonlinear Mechanical Oscillators: Part II—Resonance Capture , 2001 .

[8]  Yusuf Altintas,et al.  Analytical Prediction of Stability Lobes in Milling , 1995 .

[9]  Leonid I. Manevitch,et al.  Passive control of aeroelastic instability in a long span bridge model prone to coupled flutter using targeted energy transfer , 2011 .

[10]  Gábor Stépán,et al.  Stability of up-milling and down-milling, part 2: experimental verification , 2003 .

[11]  Gábor Stépán,et al.  Stability of up-milling and down-milling, part 1: alternative analytical methods , 2003 .

[12]  Min Wang,et al.  Feasibility study of nonlinear tuned mass damper for machining chatter suppression , 2011 .

[13]  Zoltan Dombovari,et al.  On the Global Dynamics of Chatter in the Orthogonal Cutting Model , 2011 .

[14]  Gilles Dessein,et al.  SUPPRESSION OF PERIOD DOUBLING CHATTER IN HIGH-SPEED MILLING BY SPINDLE SPEED VARIATION , 2011 .

[15]  G. Luo,et al.  PERIODIC MOTIONS AND GLOBAL BIFURCATIONS OF A TWO-DEGREE-OF-FREEDOM SYSTEM WITH PLASTIC VIBRO-IMPACT , 2001 .

[16]  Yusuf Altintas,et al.  Optimization of multiple tuned mass dampers to suppress machine tool chatter , 2010 .

[17]  Sébastien Seguy,et al.  Chatter milling modeling of active magnetic bearing spindle in high-speed domain , 2011 .

[18]  G. Kerschena,et al.  Using passive nonlinear targeted energy transfer to stabilize drill-string systems , 2008 .

[19]  Jean-Max Redonnet,et al.  Predicting the dynamic behaviour of torus milling tools when climb milling using the stability lobes theory , 2013 .

[20]  Tamás Insperger,et al.  Chatter in interrupted turning with geometrical defects: an industrial case study , 2014 .

[21]  Firas A. Khasawneh,et al.  Investigation of Period-Doubling Islands in Milling With Simultaneously Engaged Helical Flutes , 2012 .

[22]  Min Wang,et al.  Design and implementation of nonlinear TMD for chatter suppression: An application in turning processes , 2010 .

[23]  Claude-Henri Lamarque,et al.  Targeted energy transfer in mechanical systems by means of non-smooth nonlinear energy sink , 2011 .

[24]  Tamás Kalmár-Nagy,et al.  Suppression of Machine Tool Chatter Using Nonlinear Energy Sink , 2011 .

[25]  D. M. McFarland,et al.  Targeted energy transfers in vibro-impact oscillators for seismic mitigation , 2007 .

[26]  Neil D. Sims,et al.  Vibration absorbers for chatter suppression: A new analytical tuning methodology , 2007 .

[27]  G. Kerschen,et al.  Suppression Aeroelastic Instability Using Broadband Passive Targeted Energy Transfers, Part 1: Theory , 2007 .

[28]  Alexander F. Vakakis,et al.  Suppressing Aeroelastic Instability Using Broadband Passive Targeted Energy Transfers, Part 2: Experiments , 2007 .

[29]  Claude-Henri Lamarque,et al.  Vibratory energy exchange between a linear and a nonsmooth system in the presence of the gravity , 2012 .

[30]  Atsushi Matsubara,et al.  Vibration suppression of boring bar by piezoelectric actuators and LR circuit , 2014 .

[31]  S. A. Tobias,et al.  Theory of finite amplitude machine tool instability , 1984 .

[32]  Oleg Gendelman,et al.  Analytic treatment of a system with a vibro-impact nonlinear energy sink , 2012 .

[33]  Christian Brecher,et al.  Chatter suppression with an active workpiece holder , 2010, Prod. Eng..

[34]  Oleg Gendelman,et al.  Strongly modulated response in forced 2DOF oscillatory system with essential mass and potential asymmetry , 2008 .

[35]  Guilhem Michon,et al.  Delayed dynamical sytem strongly coupled to a nonlinear energy sink : application to machining chatter , 2012 .

[36]  Ali H. Nayfeh,et al.  Analysis of the cutting tool on a lathe , 2011 .

[37]  Brian P. Mann,et al.  Uncharted islands of chatter instability in milling , 2008 .

[38]  Tamás Kalmár-Nagy,et al.  Targeted Energy Transfer for Suppressing Regenerative Instabilities in a 2-DOF Machine Tool Model , 2013 .

[39]  Oleg Gendelman,et al.  Bifurcations of self-excitation regimes in a Van der Pol oscillator with a nonlinear energy sink , 2010 .