A Study of Statistical Variability in the Strength of Single Aramid Filaments

Variability in the failure load, tenacity, and linear density of single aramid filaments is studied experimentally. Data indicate that both the failure load and the tenacity of filaments, for a given gauge length and yarn cross section, can be fitted to a two parameter Weibull distribution; however the fit is better for tenacity than for failure load, and the Weibull shape parameter for the former is typically smaller. Within a yam cross section filaments vary significantly in linear density (and diameter), and this variability contributes a component to the variability in failure load, but not to the tenacity. Also, the mean tenacity and the variability in linear density and in failure load may differ greatly from spool to spool. The implications of the variability are discussed in light of the work of Bunsell. The effect of gauge length on the strength distribution of filaments is examined. Weibull statistics are used to separate out this effect. As previously shown for other brittle filaments, the Weibull shape parameter for aramid filaments depends on the gauge length; however values for the shape parameter calculated at a fixed gauge length are substantially lower than those obtained by a procedure based on varying the gauge length. This suggests short range correlations in flaw strengths along a filament.

[1]  W. Weibull.  A statistical theory of the strength of materials , 1939 .

[2]  H. Daniels.  The statistical theory of the strength of bundles of threads. I , 1945, Proceedings of the Royal Society of London. Series A. Mathematical and Physical Sciences.

[3]  Bernard D. Coleman,et al.  On the strength of classical fibres and fibre bundles , 1958 .

[4]  A. Cohen,et al.  Maximum Likelihood Estimation in the Weibull Distribution Based On Complete and On Censored Samples , 1965 .

[5]  John M. Hedgepeth,et al.  Local Stress Concentrations in Imperfect Filamentary Composite Materials , 1967 .

[6]  R. Moreton,et al.  The effect of gauge length on the tensile strength of R.A.E. carbon fibres , 1969 .

[7]  Lee J. Bain,et al.  Two Sample Tests in the Weibull Distribution , 1969 .

[8]  M. Stephens.  Use of the Kolmogorov-Smirnov, Cramer-Von Mises and Related Statistics without Extensive Tables , 1970 .

[9]  Sl Phoenix.  Probabilistic concepts in modeling the tensile strength behavior of fiber bundles and unidirectional fiber/matrix composites , 1974 .

[10]  E. Kay,et al.  Methods for statistical analysis of reliability and life data , 1974 .

[11]  R. E. Tressler,et al.  Gauge Length and Surface Damage Effects on the Strength Distributions of Silicon Carbide and Sapphire Filaments , 1975 .

[12]  A. Bunsell.  The tensile and fatigue behaviour of Kevlar-49 (PRD-49) fibre , 1975 .

[13]  N. Singpurwalla,et al.  Methods for Statistical Analysis of Reliability and Life Data. , 1975 .

[14]  C. Chiao,et al.  Experimental Verification of an Accelerated Test for Predicting the Lifetime of Organic Fiber Composites , 1977 .

[15]  A. Ciferri.  Ultra‐high‐modulus fibers from solution spinning , 1975 .

[16]  S. L. Phoenix,et al.  Asymptotic Distributions for the Failure of Fibrous Materials Under Series-Parallel Structure and Equal Load-Sharing , 1981 .

[17]  S. L. Phoenix,et al.  On Modelling the Statistical Strength of Yarns and Cables Under Localized Load-Sharing Among Fibers , 1981 .

[18]  A. Bunsell,et al.  The fatigue behaviour of Kevlar-29 fibres , 1982 .

[19]  S. L. Phoenix,et al.  STATISTICS FOR THE TIME DEPENDENT FAILURE OF KEVLAR-49/EPOXY COMPOSITES: MICROMECHANICAL MODELING AND DATA INTERPRETATION , 1983 .

[20]  R. L. Smith,et al.  A comparison of probabilistic techniques for the strength of fibrous materials under local load-sharing among fibers☆ , 1983 .

[21]  Fp Gerstle,et al.  Prediction of Long-Term Failure in Kevlar 49 Composites , 1983 .

[22]  Elisa T. Lee,et al.  Statistical Methods for Survival Data Analysis , 1994, IEEE Transactions on Reliability.