Characterizations of polybenzimidazole based electrochemical hydrogen pumps with various Pt loadings for H2/CO2 gas separation

Abstract Carbon capture and storage (CCS) technologies have been intensively researched and developed to cope with climate change, by reducing atmospheric CO2 concentration. The electrochemical hydrogen pumps with phosphoric acid doped polybenzimidazole (PBI) membrane are evaluated as a process to concentrate CO2 and produce pure H2 from anode outlet gases (H2/CO2 mixture) of molten carbonate fuel cells (MCFC). The PBI-based hydrogen pump without humidification (160 °C) can provide higher hydrogen separation performances than the cells with perfluorosulfonic-acid membranes at a relative humidity of 43% (80 °C), suggesting that the pre-treatment steps can be decreased for PBI-based systems. With the H2/CO2 mixture feed, the current efficiency for the hydrogen separation is very high, but the cell voltage increase, compared to the pure hydrogen operation, mainly due to the larger polarization resistance at electrodes, as confirmed by electrochemical impedance spectroscopy (EIS). The performance evaluation with various Pt loadings indicates that the hydrogen oxidation reaction at anodes is rate determining, and therefore the Pt loading at cathodes can be decreased from 1.1 mg/cm2 to 0.2 mg/cm2 without significant performance decay. The EIS analysis also confirms that the polarization resistances are largely dependent on the Pt loading in anodes.

[1]  Mitsuyuki Nagahama,et al.  Treatment of low concentration hydrogen by electrochemical pump or proton exchange membrane fuel cell , 2009 .

[2]  Stefano Campanari,et al.  Carbon dioxide separation from high temperature fuel cell power plants , 2002 .

[3]  Enrico Drioli,et al.  Membrane technologies for CO2 separation , 2010 .

[4]  Søren Knudsen Kær,et al.  High temperature PEM fuel cell performance characterisation with CO and CO2 using electrochemical impedance spectroscopy , 2011 .

[5]  Bert Metz,et al.  Carbon Dioxide Capture and Storage , 2005 .

[6]  G.J.M. Janssen,et al.  Modelling study of CO2 poisoning on PEMFC anodes , 2004 .

[7]  A. A. Filippov,et al.  Characterisation of a electrochemical hydrogen pump using electrochemical impedance spectroscopy , 2011 .

[8]  Edel Sheridan,et al.  Electrochemical hydrogen separation and compression using polybenzimidazole (PBI) fuel cell technology , 2010 .

[9]  Pierre Millet,et al.  Description and characterization of an electrochemical hydrogen compressor/concentrator based on solid polymer electrolyte technology , 2011 .

[10]  Chih-Hung Huang,et al.  A Review of CO2 Capture by Absorption and Adsorption , 2012 .

[11]  Ronghuan He,et al.  PBI‐Based Polymer Membranes for High Temperature Fuel Cells – Preparation, Characterization and Fuel Cell Demonstration , 2004 .

[12]  Tae Hyung Lee,et al.  Hydrogen separation using electrochemical method , 2004 .

[13]  P. Stonehart,et al.  Simulation and optimization of porous gas-diffusion electrodes used in hydrogen oxygen phosphoric acid fuel cells. II, Development of a detailed anode model , 1991 .

[14]  M. Ternan,et al.  Separation of hydrogen from hydrogen/ethylene mixtures using PEM fuel cell technology , 2009 .

[15]  T. Lim,et al.  Synthesis and characterization of acid-doped polybenzimidazole membranes by sol–gel and post-membrane casting method , 2010 .

[16]  Ronghuan He,et al.  The CO Poisoning Effect in PEMFCs Operational at Temperatures up to 200°C , 2003 .

[17]  Brian C. Benicewicz,et al.  Electrochemical hydrogen pumping using a high-temperature polybenzimidazole (PBI) membrane , 2008 .

[18]  Mitsuyuki Nagahama,et al.  Separation and compression characteristics of hydrogen by use of proton exchange membrane , 2007 .

[19]  W. Lai,et al.  Effects of temperature and humidity on the cell performance and resistance of a phosphoric acid doped polybenzimidazole fuel cell , 2010 .

[20]  C. L. Gardner,et al.  Electrochemical separation of hydrogen from reformate using PEM fuel cell technology , 2007 .

[21]  Jian Colin Sun,et al.  AC impedance technique in PEM fuel cell diagnosis—A review , 2007 .

[22]  Marten Ternan,et al.  Separation of hydrogen from a hydrogen/methane mixture using a PEM fuel cell , 2007 .

[23]  Suk Woo Nam,et al.  Demonstration of a 20 W class high-temperature polymer electrolyte fuel cell stack with novel fabrication of a membrane electrode assembly , 2011 .

[24]  Dong Hoon Lee,et al.  Synthesis and Characterization of H3PO4 Doped Poly(benzimidazole-co-benzoxazole) Membranes for High Temperature Polymer Electrolyte Fuel Cells , 2012 .

[25]  J. Gibbins,et al.  Carbon Capture and Storage , 2008 .

[26]  Hossein Toghiani,et al.  Investigation of water transport through membrane in a PEM fuel cell by water balance experiments , 2006 .