Effect of martensite morphology and volume fraction on strain hardening and fracture behavior of martensite–ferrite dual phase steel

Abstract Two different morphologies of martensite in dual phase (DP) steel were obtained using two different processing routes. In one case, intermediate quenching (IQ) was adapted, where DP steel was water-quenched to obtain martensite phase, followed by inter-critical annealing. In the second case, the steel was cold rolled, followed by inter-critical annealing (CR-IA). For IQ and CR-IA steels, the inter-critical temperatures varied from 750 °C to 850 °C to obtain different volume fractions of martensite. An understanding of structure–property was obtained using a combination of scanning electron microscope (SEM), transmission electron microscope (TEM), and tensile tests. It was observed that fibrous martensite presented in IQ samples, gradually transformed to blocky martensite with increase in inter-critical temperature, resembling the CR-IA steels. The fibrous martensite encouraged martensite cracking, however, the martensite cracking was dramatically decreased in the IQ samples with increase in martensite fraction. The strain hardening behavior studied using the differential C – J model indicated multistage depending on the fraction of martensite. The low volume fraction of martensite in the DP steel provided high ductility–toughness combination and improved strain hardening ability due to the presence of soft ferrite phase in DP steel. Fibrous martensite in DP steel resulted in less strain hardening than blocky martensite, prior to exceeding a threshold volume fraction. The threshold value was significantly smaller for DP steel with blocky martensite.

[1]  A. Preban,et al.  The effect of ferrite grain size and martensite volume fraction on the tensile properties of dual phase steel , 1985 .

[2]  P. Chattopadhyay,et al.  Influence of martensite morphology on the work-hardening behavior of high strength ferrite–martensite dual-phase steel , 2009 .

[3]  C. Tasan,et al.  Hydrogen-assisted decohesion and localized plasticity in dual-phase steel , 2014 .

[4]  T. Byun,et al.  Tensile properties and inhomogeneous deformation of ferrite-martensite dual-phase steels , 1993, Journal of Materials Science.

[5]  Aydin Hüseyin,et al.  Effect of intercritical annealing parameters on dual phase behavior of commercial low-alloyed steels , 2010 .

[6]  J. D. Boyd,et al.  Effect of pre-IC annealing treatments on the final microstructure and work hardening behavior of a dual-phase steel , 2014 .

[7]  George Krauss,et al.  The effect of microstructure and strain rate on the stage III strain hardening and ductility of dual-phase steels , 1987 .

[8]  S. Monteiro,et al.  On the double-n behavior of iron , 1971 .

[9]  E. Kröner,et al.  On the physical reality of torque stresses in continuum mechanics , 1963 .

[10]  Michael R. Notis,et al.  Continuous cooling transformation kinetics versus isothermal transformation kinetics of steels: a phenomenological rationalization of experimental observations , 1995 .

[11]  V. Uthaisangsuk,et al.  Microstructure based prediction of strain hardening behavior of dual phase steels , 2012 .

[12]  M. Calcagnotto,et al.  Orientation gradients and geometrically necessary dislocations in ultrafine grained dual-phase steels studied by 2D and 3D EBSD , 2010 .

[13]  Dierk Raabe,et al.  Deformation and fracture mechanisms in fine- and ultrafine-grained ferrite/martensite dual-phase steels and the effect of aging , 2011 .

[14]  Minoru Umemoto,et al.  Tensile stress-strain analysis of single-structure steels , 2000 .

[15]  B. Grushko,et al.  Yield behaviour of dual-phase steel , 1989 .

[16]  D. Chakrabarti,et al.  Cold-rolling and inter-critical annealing of low-carbon steel: Effect of initial microstructure and heating-rate , 2013 .

[17]  Jpm Johan Hoefnagels,et al.  Indentation-based damage quantification revisited , 2010 .

[18]  M. Calcagnotto,et al.  On the Effect of Manganese on Grain Size Stability and Hardenability in Ultrafine-Grained Ferrite/Martensite Dual-Phase Steels , 2011, Metallurgical and Materials Transactions A.

[19]  J. Nye.  Some geometrical relations in dislocated crystals , 1953 .

[20]  E. Fereiduni,et al.  Ferrite hardening response in a low alloy ferrite–martensite dual phase steel , 2014 .

[21]  W. S. Owen,et al.  The work hardening of dual-phase steels at small plastic strains , 1984 .

[22]  M. Chaturvedi,et al.  On the effect of the volume fraction on martensite on the tensile strength of dual-phase steel , 1988 .

[23]  F. Barlat,et al.  Evaluation of Fracture Micromechanisms in a Fine‐Grained Dual Phase Steel during Uniaxial Tensile Deformation , 2014 .

[24]  R. G. Davies.  Early stages of yielding and strain aging of a vanadium-containing dual-phase steel , 1979 .

[25]  M. Calcagnotto,et al.  Effect of grain refinement to 1 μm on strength and toughness of dual-phase steels , 2010 .

[26]  G. Krauss.  Martensite in steel: strength and structure , 1999 .

[27]  B. Niroumand,et al.  Development of a new ultrafine grained dual phase steel and examination of the effect of grain size on tensile deformation behavior , 2014 .

[28]  Christophe Pinna,et al.  Local plastic strain evolution in a high strength dual-phase steel , 2010 .

[29]  Saeed Ziaei-Rad,et al.  Experimental and numerical study on geometrically necessary dislocations and non-homogeneous mechanical properties of the ferrite phase in dual phase steels , 2011 .

[30]  K. Hulka.  Modern Multi-Phase Steels for the Automotive Industry , 2002 .

[31]  M. Ashby.  The deformation of plastically non-homogeneous materials , 1970 .

[32]  F. Roters,et al.  Microstructure and texture evolution in dual-phase steels: Competition between recovery, recrystallization, and phase transformation , 2010 .

[33]  D. Bourell,et al.  Dislocation density contribution to strength of dual-phase steels , 1982 .

[34]  K. S. Choi,et al.  Predicting failure modes and ductility of dual phase steels using plastic strain localization , 2009 .

[35]  E. Fereiduni,et al.  Improvement of mechanical properties in a dual-phase ferrite–martensite AISI4140 steel under tough-strong ferrite formation , 2014 .

[36]  T. Gladman,et al.  Work hardening of dual-phase steels , 1981 .

[37]  Toshihiro Tsuchiyama,et al.  Effect of the martensite distribution on the strain hardening and ductile fracture behaviors in dual-phase steel , 2014 .

[38]  L. Rong,et al.  Microstructural evolution and mechanical properties of heat affected zones for 9Cr2WVTa steels with different carbon contents , 2014 .

[39]  E. Werner,et al.  An unexpected feature of the stress–strain diagram of dual-phase steel , 2002 .

[40]  B. M. Patchett,et al.  Observation of twinned martensite in weld heat affected zone of Grade 100 low carbon microalloyed steel , 2004 .