APPLICATION OF THE DISCRETE ELEMENT MODELLING IN AIR DRYING OF PARTICULATE SOLIDS

ABSTRACT The Discrete Element Method (DEM) has been widely used as a mathematical tool for the study of flow characteristics involving particulate solids. One distinct advantage of this fast developing technique is the ability to compute trajectories of discrete particles. This provides the opportunity to evaluate the interactions between particle, fluid and boundary at the microscopic level using local gas parameters and properties, which is difficult to achieve using a continuum model. To date, most of these applications focus on the flow behaviour. This paper provides an overview of the application of DEM in gas–solids flow systems and discusses further development of this technique in the application of drying particulate solids. A number of sub-models, including momentum, energy and mass transfer, have been evaluated to describe the various transport phenomena. A numerical model has been developed to calculate the heat transfer in a gas–solids pneumatic transport line. This implementation has shown advantages of this method over conventional continuum approaches. Future application of this technique in drying technology is possible but experimental validation is crucial.

[1]  I. Schwedes.  Processing of Particulate Solids , 1999 .

[2]  Y. Tsuji,et al.  Discrete particle simulation of two-dimensional fluidized bed , 1993 .

[3]  Arun S. Mujumdar,et al.  Advances in drying , 1980 .

[4]  Avi Levy,et al.  Drying of wet solid particles in a steady-state one-dimensional flow , 1998 .

[5]  P. A. Langston,et al.  Distinct element simulation of interstitial air effects in axially symmetric granular flows in hoppers , 1996 .

[6]  Efstathios E. Michaelides,et al.  A model for the flow of solid particles in gases , 1983 .

[7]  Yutaka Tsuji,et al.  Lagrangian numerical simulation of plug flow of cohesionless particles in a horizontal pipe , 1992 .

[8]  A. V. Luikov,et al.  CHAPTER 6 – HEAT AND MASS TRANSFER IN CAPILLARY-POROUS BODIES , 1966 .

[9]  D. Mason,et al.  A computational investigation of transient heat transfer in pneumatic transport of granular particles , 2000 .

[10]  D. Pei,et al.  A mathematical analysis of pneumatic drying of grains—I. Constant drying rate , 1984 .

[11]  L. Schiller.  Uber die Grundlegenden Berechnungen bei der Schwerkraftaufbereitung , 1933 .

[12]  D. A. Wrangham.  The Elements of Heat Flow , 1961 .

[13]  M. T. Mason,et al.  Two-Dimensional Rigid-Body Collisions With Friction , 1992 .

[14]  F. Yamamoto.  A Study of Motion of a Sphere in Air Flow through Horizontal Pipe , 1986 .

[15]  Th. Frank,et al.  NUMERICAL SIMULATION AND EXPERIMENTAL INVESTIGATION OF A GAS-SOLID TWO-PHASE FLOW IN A HORIZONTAL CHANNEL , 1993 .

[16]  Shozaburo Saito,et al.  ON THE MECHANISM OF SUSPENSION OF PARTICLES IN HORIZONTAL PNEUMATIC CONVEYING: MONTE CARLO SIMULATION BASED ON THE IRREGULAR BOUNCING MODEL , 1970 .

[17]  Yong Li,et al.  Numerical simulation of gas–liquid–solid fluidization systems using a combined CFD-VOF-DPM method: bubble wake behavior , 1999 .

[18]  J. Bandrowski,et al.  Gas-to-particle heat transfer in vertical pneumatic conveying of granular materials , 1978 .

[19]  P. Cundall,et al.  A discrete numerical model for granular assemblies , 1979 .

[20]  Nicholas M. Spyrou,et al.  Microstructural simulation and imaging of granular flows in two- and three-dimensional hoppers , 1997 .

[21]  Y. Tomita,et al.  Motion of a single particle in a horizontal pipe , 1996 .

[22]  Jonathan Seville,et al.  Storage and discharge of particulate bulk solids , 1997 .

[23]  G.S.V. Raghavan,et al.  A Mathematical Model for Constant and Intermittent Batch Drying of Grains in a Novel Rotating Jet Spouted bed , 1996 .

[24]  Martin R. Okos,et al.  CLASSIFICATION OF DRYING MODELS FOR POROUS SOLIDS , 1993 .

[25]  P. A. Langston,et al.  Discrete element simulation of granular flow in 2D and 3D hoppers: Dependence of discharge rate and wall stress on particle interactions , 1995 .

[26]  F. H. Garner,et al.  Chemical Engineering , 1955, Nature.

[27]  D. Brian Spalding,et al.  Numerical computation of multi-phase fluid flow and heat transfer , 1980 .

[28]  M. M. Chen,et al.  A theoretical analysis of heat transfer due to particle impact , 1988 .

[29]  Colin Thornton,et al.  Impact of elastic spheres with and without adhesion , 1991 .

[30]  S. Ergun.  Fluid flow through packed columns , 1952 .

[31]  Mihail C. Roco,et al.  Particulate two-phase flow , 1993 .

[32]  J. A. Ottjes.  Digital simulation of pneumatic particle transport , 1978 .

[33]  Yuji Tomita,et al.  Effect of Particle-Particle Collision and Particle Rotation upon Floating Mechanism of Coarse Particles in Horizontal Pneurnatic Pipe , 1994 .

[34]  J. Kuipers,et al.  A numerical model of gas-fluidized beds , 1992 .

[35]  David J. Mason,et al.  A novel experimental technique for the investigation of gas–solids flow in pipes , 2000 .

[36]  C. Crowe,et al.  The Particle-Source-In Cell (PSI-CELL) Model for Gas-Droplet Flows , 1977 .

[37]  R. G. Boothroyd,et al.  Flowing gas-solids suspensions , 1971 .

[38]  J. Kuipers,et al.  Discrete particle simulation of bubble and slug formation in a two-dimensional gas-fluidised bed: A hard-sphere approach. , 1996 .

[39]  A. Dukler,et al.  An eddy viscosity model for friction in gas—solids flow , 1965 .

[40]  Avi Levy,et al.  Mathematical Modeling of Drying of Liquid/Solid Slurries in Steady State One-Dimensional Flow , 1995 .

[41]  Martin Sommerfeld,et al.  MODELLING OF PARTICLE-WALL COLLISIONS IN CONFINED GAS-PARTICLE FLOWS , 1992 .

[42]  David John Mason.  A study of the modes of gas-solids flow in pipelines , 1991 .

[43]  D. Pei,et al.  A mathematical analysis of pneumatic drying of grains—II. Falling rate drying , 1984 .

[44]  Relative contributions from particle conduction and gas convection to the heat transfer coefficient between dense gas-solid fluidized beds and surfaces , 1997 .