Rheological behavior of multiwalled carbon nanotube/polycarbonate composites

Abstract The rheological behavior of compression molded mixtures of polycarbonate containing between 0.5 and 15 wt% carbon nanotubes was investigated using oscillatory rheometry at 260 °C. The nanotubes have diameters between 10 and 15 nm and lengths ranging from 1 to 10 μm. The composites were obtained by diluting a masterbatch containing 15 wt% nanotubes using a twin-screw extruder. The increase in viscosity associated with the addition of nanotubes is much higher than viscosity changes reported for carbon nanofibers having larger diameters and for carbon black composites; this can be explained by the higher aspect ratio of the nanotubes. The viscosity increase is accompanied by an increase in the elastic melt properties, represented by the storage modulus G ′, which is much higher than the increase in the loss modulus G ″. The viscosity curves above 2 wt% nanotubes exhibit a larger decrease with frequency than samples containing lower nanotube loadings. Composites containing more than 2 wt% nanotubes exhibit non-Newtonian behavior at lower frequencies. A step increase at approximately 2 wt% nanotubes was observed in the viscosity–composition curves at low frequencies. This step change may be regarded as a rheological threshold. Ultimately, the rheological threshold coincides with the electrical conductivity percolation threshold which was found to be between 1 and 2 wt% nanotubes.

[1]  Milo S. P. Shaffer,et al.  Dispersion and packing of carbon nanotubes , 1998 .

[2]  S. Havriliak,et al.  Dielectric and Mechanical Relaxation in Materials: Analysis, Interpretation and Application to Polymers , 1996 .

[3]  Jinhwan Kim,et al.  Rheological technique for determining the order–disorder transition of block copolymers , 1987 .

[4]  T. Kitano,et al.  Shear flow rheological properties of vinylon- and glass-fiber reinforced polyethylene melts , 1984 .

[5]  Deron A. Walters,et al.  Elastic strain of freely suspended single-wall carbon nanotube ropes , 1999 .

[6]  Linda S. Schadler,et al.  LOAD TRANSFER IN CARBON NANOTUBE EPOXY COMPOSITES , 1998 .

[7]  Elizabeth C. Dickey,et al.  Load transfer and deformation mechanisms in carbon nanotube-polystyrene composites , 2000 .

[8]  Serge Lefrant,et al.  Characterization of singlewalled carbon nanotubes-PMMA composites , 2000 .

[9]  Karen Lozano,et al.  A study on nanofiber-reinforced thermoplastic composites (II): Investigation of the mixing rheology and conduction properties , 2001 .

[10]  Aroon Shenoy,et al.  Rheology of Filled Polymer Systems , 1999 .

[11]  T. Kitano,et al.  The effect of the mixing methods on viscous properties of polyethylene melts filled with fibers , 1980 .

[12]  Isaac Balberg,et al.  Recent developments in continuum percolation , 1987 .

[13]  L. A. Utracki,et al.  Flow and flow orientation of composites containing anisometric particles , 1986 .

[14]  Hui-Ming Cheng,et al.  Tensile strength of single-walled carbon nanotubes directly measured from their macroscopic ropes , 2000 .

[15]  L. Utracki.  Two-Phase Polymer Systems , 1991 .

[16]  K. Cole,et al.  Dispersion and Absorption in Dielectrics I. Alternating Current Characteristics , 1941 .

[17]  A. Rinzler,et al.  ALIGNED SINGLE-WALL CARBON NANOTUBES IN COMPOSITES BY MELT PROCESSING METHODS , 2000 .

[18]  Otto Zhou,et al.  Alignment of carbon nanotubes in a polymer matrix by mechanical stretching , 1998 .

[19]  G. A. D. Briggs,et al.  Elastic and shear moduli of single-walled carbon nanotube ropes , 1999 .

[20]  Otto Zhou,et al.  Deformation of carbon nanotubes in nanotube–polymer composites , 1999 .

[21]  K. Lozano,et al.  Nanofiber‐reinforced thermoplastic composites. I. Thermoanalytical and mechanical analyses , 2001 .

[22]  M. Shaffer,et al.  Fabrication and Characterization of Carbon Nanotube/Poly(vinyl alcohol) Composites , 1999 .

[23]  Angel Rubio,et al.  Single‐Walled Carbon Nanotube–Polymer Composites: Strength and Weakness , 2000 .

[24]  P. Bernier,et al.  Raman characterization of singlewalled carbon nanotubes and PMMA-nanotubes composites , 1999 .

[25]  F. Cogswell.  Melt Rheology and its Role in Plastic Processing: Theory and Applications : by J.M. Dealy and K.F. Wissbrun, Van Nostrand Reinhold, 665 pp., New York, 1990, $S74.95. , 1991 .

[26]  G. Xu,et al.  Dynamic mechanical behavior of melt-processed multi-walled carbon nanotube/poly(methyl methacrylate) composites , 2001 .

[27]  A. Rinzler,et al.  Electronic structure of atomically resolved carbon nanotubes , 1998, Nature.

[28]  A. Dalton,et al.  Physical Doping of a Conjugated Polymer with Carbon Nanotubes , 1999 .

[29]  N. Nakajima,et al.  Modified Cole–Cole plot based on viscoelastic properties for characterizing molecular architecture of elastomers , 1984 .

[30]  Jinhwan Kim,et al.  Determination of the order-disorder transition temperature of block copolymers , 1989 .

[31]  D. R. Paul,et al.  Nylon 6 nanocomposites by melt compounding , 2001 .

[32]  Milo S. P. Shaffer,et al.  Development of a dispersion process for carbon nanotubes in an epoxy matrix and the resulting electrical properties , 1999 .

[33]  C. Lieber,et al.  Atomic structure and electronic properties of single-walled carbon nanotubes , 1998, Nature.

[34]  T. D. Fornes,et al.  Nylon 6 nanocomposites: the effect of matrix molecular weight , 2001 .

[35]  S. Subramoney.  Novel Nanocarbons—Structure, Properties, and Potential Applications , 1998 .

[36]  C. Han,et al.  Rheological behavior of polymer blends , 1984 .