High Power Density Body Heat Energy Harvesting.

Thermoelectric generators (TEGs) can convert body heat into electricity, thereby, providing a continuous power source for wearable and implantable devices. For wearables, the low fill factor (area occupied by legs over TEG base area) TEG modules are relevant as they provide large thermal gradient across the legs and require less material, which reduces the cost and weight. However, TEGs with fill factor below 15% suffer from reduced mechanical robustness, consequently, commercial modules are usually fabricated with fill factor in the range of 25-50%. In this study, TEG modules with low and high fill factor are demonstrated and their performance is compared in harvesting body heat. Fabricated modules demonstrate ~80% output power enhancement as compared to commercially available designs, resulting in high power density up to 35 μW/cm2 in steady-state. This enhanced power is achieved by using two-third less thermoelectric materials in comparison to commercial modules. These results will advance the ongoing development of wearable devices by providing a consistent high specific power density source.

[1]  G. Joshi,et al.  A quick and efficient measurement technique for performance evaluation of thermoelectric materials , 2016 .

[2]  Vladimir Leonov,et al.  Thermoelectric Energy Harvesting of Human Body Heat for Wearable Sensors , 2013, IEEE Sensors Journal.

[3]  Sheng Xu,et al.  Wearable thermoelectrics for personalized thermoregulation , 2019, Science Advances.

[4]  Ashiqur Rahman,et al.  An overview of cooling of thermoelectric devices , 2017 .

[5]  Chris Van Hoof,et al.  Realization of a wearable miniaturized thermoelectric generator for human body applications , 2009 .

[6]  Edward Arens,et al.  Indoor Environmental Quality ( IEQ ) Title A model of human physiology and comfort for assessing complex thermal environments , 2001 .

[7]  J. Ji,et al.  Recent development and application of thermoelectric generator and cooler , 2015 .

[8]  L. Bell.  Cooling, Heating, Generating Power, and Recovering Waste Heat with Thermoelectric Systems , 2008, Science.

[9]  Mohan Sanghadasa,et al.  Ultra-high performance wearable thermoelectric coolers with less materials , 2019, Nature Communications.

[10]  T. Liang,et al.  High thermoelectric performance of mechanically robust n-type Bi2Te3−xSex prepared by combustion synthesis , 2015 .

[11]  Qian Zhang,et al.  Thermoelectric Property Studies on Cu‐Doped n‐type CuxBi2Te2.7Se0.3 Nanocomposites , 2011 .

[12]  O. D. Iyore,et al.  Determination of Contact Resistivity by the Cox and Strack Method for Metal Contacts to Bulk Bismuth Antimony Telluride , 2009 .

[13]  B. Cho,et al.  Flexible heatsink based on a phase-change material for a wearable thermoelectric generator , 2019, Energy.

[14]  Byeong Kwon Ju,et al.  Design and Experimental Investigation of Thermoelectric Generators for Wearable Applications , 2017 .

[15]  M. Dresselhaus,et al.  High-Thermoelectric Performance of Nanostructured Bismuth Antimony Telluride Bulk Alloys , 2008, Science.

[16]  G. J. Snyder,et al.  Complex thermoelectric materials. , 2008, Nature materials.

[17]  Dongkeon Lee,et al.  High power output based on watch-strap-shaped body heat harvester using bulk thermoelectric materials , 2019, Energy.

[18]  Marianne Lossec,et al.  Thermoelectric generator placed on the human body: system modeling and energy conversion improvements , 2010 .

[19]  SeongHwan Cho,et al.  Self-Powered Wearable Electrocardiography Using a Wearable Thermoelectric Power Generator , 2018 .

[20]  P. Webb.  Temperatures of skin, subcutaneous tissue, muscle and core in resting men in cold, comfortable and hot conditions , 2004, European Journal of Applied Physiology and Occupational Physiology.

[21]  Chen Ming,et al.  Realizing a thermoelectric conversion efficiency of 12% in bismuth telluride/skutterudite segmented modules through full-parameter optimization and energy-loss minimized integration , 2017 .

[22]  Yong Zhu,et al.  Flexible Technologies for Self-Powered Wearable Health and Environmental Sensing , 2015, Proceedings of the IEEE.

[23]  Luca Benini,et al.  Human body heat for powering wearable devices: From thermal energy to application , 2017 .

[24]  Mehmet C. Öztürk,et al.  Designing thermoelectric generators for self-powered wearable electronics , 2016 .

[25]  Raziel Riemer,et al.  Biomechanical energy harvesting from human motion: theory, state of the art, design guidelines, and future directions , 2011, Journal of NeuroEngineering and Rehabilitation.

[26]  Mehmet C. Öztürk,et al.  Flexible thermoelectric generator using bulk legs and liquid metal interconnects for wearable electronics , 2017 .

[27]  Amin Nozariasbmarz,et al.  N-Type Bismuth Telluride Nanocomposite Materials Optimization for Thermoelectric Generators in Wearable Applications , 2019, Materials.

[28]  Ji-Hui Yang,et al.  Automotive Applications of Thermoelectric Materials , 2009 .