Characterization of the harvesting capabilities of an ionic polymer metal composite device

Harvesting systems capable of transforming dusty environmental energy into electrical energy have aroused considerable interest in the last two decades. Several research works have focused on the transformation of mechanical environmental vibrations into electrical energy. Most of the research activity refers to classic piezoelectric ceramic materials, but more recently piezoelectric polymer materials have been considered. In this paper, a novel point of view regarding harvesting systems is proposed: using ionic polymer metal composites (IPMCs) as generating materials. The goal of this paper is the development of a model able to predict the energy harvesting capabilities of an IPMC material working in air. The model is developed by using the vibration transmission theory of an Euler?Bernoulli cantilever IPMC beam. The IPMC is considered to work in its linear elastic region with a viscous damping contribution ranging from 0.1 to 100?Hz. An identification process based on experimental measurements performed on a Nafion? 117 membrane is used to estimate the material parameters. The model validation shows a good agreement between simulated and experimental results. The model is used to predict the optimal working region and the optimal geometrical parameters for the maximum power generation capacity of a specific membrane. The model takes into account two restrictions. The first is due to the beam theory, which imposes a maximum ratio of 0.5 between the cantilever width and length. The second restriction is to force the cantilever to oscillate with a specific strain; in this paper a 0.3% strain is considered. By considering these two assumptions as constraints on the model, it is seen that IPMC materials could be used as low-power generators in a low-frequency region. The optimal dimensions for the Nafion? 117 membrane are length = ?12?cm and width = ?6.2?cm, and the electric power generation is 3?nW at a vibrating frequency of 7.09?rad?s?1. IPMC materials can sustain big yield strains, so by increasing the strain allowed on the material the power will increase dramatically, the expected values being up to a few microwatts.

[1]  Thad Starner,et al.  Human-Powered Wearable Computing , 1996, IBM Syst. J..

[2]  K. Kim,et al.  Ionic polymer–metal composites: IV. Industrial and medical applications , 2005 .

[3]  Heath Hofmann,et al.  Adaptive piezoelectric energy harvesting circuit for wireless remote power supply , 2002 .

[4]  M. A. Trindade,et al.  Modeling of Frequency-Dependent Viscoelastic Materials for Active-Passive Vibration Damping , 2000 .

[5]  S. Graziani,et al.  Improved Frequency Investigation of IPMC Based Sensors , 2006, 2006 IEEE Instrumentation and Measurement Technology Conference Proceedings.

[6]  M. Puig-Vidal,et al.  Piezoelectric polymer model validation applied to mm size micro-robot I-SWARM (intelligent swarm) , 2006, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[7]  K. Kim,et al.  Ionic polymer-metal composites: I. Fundamentals , 2001 .

[8]  K. Kim,et al.  The effect of surface-electrode resistance on the performance of ionic polymer-metal composite (IPMC) artificial muscles , 2000 .

[9]  D. Inman,et al.  Comparison of Piezoelectric Energy Harvesting Devices for Recharging Batteries , 2005 .

[10]  Mohsen Shahinpoor,et al.  Ionic Polymer-Metal Composites (IPMC) as Biomimetric Sensors and Actuators-Artificial Muscles , 1998 .

[11]  K. Sadeghipour,et al.  Development of a novel electrochemically active membrane and 'smart' material based vibration sensor/damper , 1992 .

[12]  Luigi Fortuna,et al.  A model for ionic polymer metal composites as sensors , 2006 .

[13]  R. B. Yates,et al.  Analysis Of A Micro-electric Generator For Microsystems , 1995, Proceedings of the International Solid-State Sensors and Actuators Conference - TRANSDUCERS '95.

[14]  S. Nemat-Nasser Micromechanics of actuation of ionic polymer-metal composites , 2002 .

[15]  J. O. Simpson,et al.  Ionic polymer-metal composites (IPMCs) as biomimetic sensors, actuators and artificial muscles - a review , 1998 .

[16]  M. Umeda,et al.  Analysis of the Transformation of Mechanical Impact Energy to Electric Energy Using Piezoelectric Vibrator , 1996 .

[17]  Jan M. Rabaey,et al.  A study of low level vibrations as a power source for wireless sensor nodes , 2003, Comput. Commun..

[18]  Donald J. Leo,et al.  Linear Electromechanical Model of Ionic Polymer Transducers -Part I: Model Development , 2003 .

[19]  Kevin M. Farinholt,et al.  Constitutive Equations for an Induced-Strain Bending Actuator with a Variable Substrate , 2003 .