The temperature distribution and electrical performance of fluid heat exchanger-based thermoelectric generator

Abstract Thermoelectric generator (TEG) has great potential in waste heat recovery. In this paper a TEG system has been build up which consists of a Bi 2 Te 3 -based thermoelectric module and two fluid heat exchangers. The temperature distribution, electrical performance and heat components of the system have been investigated via both experiment and numerical simulation. It is revealed that the influence of fluid velocity on the temperature distribution is weak until the velocity is very slow, and the influence of Peltier effect on the temperature distribution is also limited in this system. Furthermore, attention should be paid to the contact electrical resistance induced by soldering, especially when the hot side temperature of the Bi 2 Te 3 module is expected up to 473 K. Besides that, heat component analysis suggests that Peltier effect should not be ignored in optimization analysis of thermoelectric module.

[1]  K. Goodson,et al.  Material and manufacturing cost considerations for thermoelectrics , 2014 .

[2]  Ali Shakouri,et al.  Cost-efficiency trade-off and the design of thermoelectric power generators. , 2011, Environmental science & technology.

[3]  Takeshi Kajihara,et al.  Thermoelectric Generation Using Waste Heat in Steel Works , 2014, Journal of Electronic Materials.

[4]  Jian He,et al.  High temperature thermoelectric properties of skutterudite-Bi2Te3 nanocomposites , 2016 .

[5]  Wei Zhu,et al.  A novel self-powered wireless temperature sensor based on thermoelectric generators , 2014 .

[6]  Guangqiang Li,et al.  Pushing the optimal ZT values of p-type Bi2−xSbxTe3 alloys to a higher temperature by expanding band gaps and suppressing intrinsic excitation , 2016, Journal of Materials Science: Materials in Electronics.

[7]  Guangqiang Li,et al.  Thermal stability of p-type polycrystalline Bi2Te3-based bulks for the application on thermoelectric power generation , 2017 .

[8]  Jing-Hui Meng,et al.  Characteristics analysis and parametric study of a thermoelectric generator by considering variable material properties and heat losses , 2015 .

[9]  Ryosuke O. Suzuki,et al.  Mathematic simulation on thermoelectric power generation with cylindrical multi-tubes , 2003 .

[10]  Yoshikazu Shinohara.  The State of the Art on Thermoelectric Devices in Japan , 2015 .

[11]  Stephen D. Heister,et al.  Thermoelectric Generators for Automotive Waste Heat Recovery Systems Part I: Numerical Modeling and Baseline Model Analysis , 2013, Journal of Electronic Materials.

[12]  M. Lazard,et al.  Modeling a Thermoelectric Generator Applied to Diesel Automotive Heat Recovery , 2010 .

[13]  Y. D. Deng,et al.  Research on the Compatibility of the Cooling Unit in an Automotive Exhaust-based Thermoelectric Generator and Engine Cooling System , 2013, Journal of Electronic Materials.

[14]  Lauryn L. Baranowski,et al.  Effective thermal conductivity in thermoelectric materials , 2013 .

[15]  Guangqiang Li,et al.  Microwave activated hot pressing: A new opportunity to improve the thermoelectric properties of ntype Bi2Te3 xSex bulks , 2016 .

[16]  Aliakbar Akbarzadeh,et al.  Performance and reliability of commercially available thermoelectric cells for power generation , 2016 .

[17]  Gao Min,et al.  Evaluation of thermoelectric modules for power generation , 1998 .

[18]  Shannon K. Yee,et al.  $ per W metrics for thermoelectric power generation: beyond ZT , 2013 .

[19]  Gaowei Liang,et al.  Analytical model of parallel thermoelectric generator , 2011 .

[20]  Ryosuke O. Suzuki,et al.  Mathematical simulation of thermoelectric power generation with the multi-panels , 2003 .