Assessment of 3D-printed span change structures applied to small unmanned aerial vehicles

An assessment of 3D-printed span-change structures is presented for determining suitability of the technology to small unmanned aerial vehicles. Materials and manufacturing technologies were used with an emphasis on near term applicability with design trades between the aerodynamic performance and structural response. Aerodynamic performance was assessed on three wind tunnel models varying span (432, 600, and 762 mm), wind speed (Reynolds numbers 18,000, 36,000, and 71,000), additive manufacturing print build plane and camber, quantifying structural response as the resulting shape during aerodynamic loading. Each model displayed increasing compliance as span increased with wing-tip displacement on the order of 50, 100, and 200 mm with various degrees of sweep and twist. Models generated excess lift at Re = 71,000 indicating potential flight demonstration of the technology with a lift to drag improvement of up to 97% at maximum wing extension.

[1]  Kenneth E. Evans,et al.  Auxetic materials: the positive side of being negative , 2000 .

[2]  Sondipon Adhikari,et al.  An integrated conceptual design study using span morphing technology , 2014 .

[3]  Sergio Ricci,et al.  Design, Manufacturing and Wind Tunnel Validation of a Morphing Compliant Wing , 2018, Journal of Aircraft.

[4]  J. Vale,et al.  Aero-Structural Optimization and Performance Evaluation of a Morphing Wing with Variable Span and Camber , 2011 .

[5]  K. Leong,et al.  Investigation of the mechanical properties and porosity relationships in fused deposition modelling‐fabricated porous structures , 2006 .

[6]  Ed Habtour,et al.  Impact mechanics of topologically interlocked material assemblies , 2015 .

[7]  Edward J. Garboczi,et al.  AMB2018-04: Benchmark Physical Property Measurements for Powder Bed Fusion Additive Manufacturing of Polyamide 12 , 2019, Integrating Materials and Manufacturing Innovation.

[8]  B. Baufeld,et al.  Additive manufacturing of Ti–6Al–4V components by shaped metal deposition: Microstructure and mechanical properties , 2010 .

[9]  M. I. Friswell,et al.  The prospects for morphing aircraft , 2009 .

[10]  Dimitris C. Lagoudas,et al.  Aerospace applications of shape memory alloys , 2007 .

[11]  Alejandro H. Espera,et al.  Mechanical characterization of 3D-printed polymers , 2018 .

[12]  Tang Huiping,et al.  Research on Preheating of Titanium Alloy Powder in Electron Beam Melting Technology , 2011 .

[13]  Manfred Morari,et al.  Design, realization and structural testing of a compliant adaptable wing , 2015 .

[14]  Luis Matey,et al.  PolyJet technology for product prototyping: Tensile strength and surface roughness properties , 2014 .

[15]  Srinivas Vasista,et al.  Realization of Morphing Wings: A Multidisciplinary Challenge , 2012 .

[16]  Y. Bar-Cohen.  Electroactive Polymers as Artificial Muscles: Capabilities, Potentials and Challenges , 2000 .

[17]  Mary Frecker,et al.  Aircraft Structural Morphing Using Tendon-Actuated Compliant Cellular Trusses , 2005 .

[18]  F. Melchels,et al.  A review on stereolithography and its applications in biomedical engineering. , 2010, Biomaterials.

[19]  John Yen,et al.  Design and Implementation of a Shape Memory Alloy Actuated Reconfigurable Airfoil , 2003 .

[20]  Yanju Liu,et al.  Morphing aircraft based on smart materials and structures: A state-of-the-art review , 2016 .

[21]  Terrence A. Weisshaar,et al.  Morphing Aircraft Systems: Historical Perspectives and Future Challenges , 2013 .

[22]  Robert P. Dahlgren,et al.  3D scanning and printing of airfoils for modular UAS , 2017, LASE.

[23]  Stefan Gottschalk,et al.  Aerodynamics Aeronautics And Flight Mechanics , 2016 .

[24]  William A. Crossley,et al.  Comparison of Morphing Wing Strategies Based Upon Aircraft Performance Impacts , 2004 .

[25]  Jakob A Faber,et al.  Bioinspired spring origami , 2018, Science.

[26]  Jae-Sung Bae,et al.  Aerodynamic and Static Aeroelastic Characteristics of a Variable-Span Morphing Wing , 2005 .

[27]  Gregory W. Reich,et al.  Introduction to Morphing Aircraft Research , 2007 .

[28]  Farhan Gandhi,et al.  Skin design studies for variable camber morphing airfoils , 2008 .

[29]  Jordi Llumà,et al.  Mechanical property characterization and simulation of fused deposition modeling Polycarbonate parts , 2015 .

[30]  Daniel J. Inman,et al.  A Review of Morphing Aircraft , 2011 .

[31]  Farhan Gandhi,et al.  Flexible Skins for Morphing Aircraft Using Cellular Honeycomb Cores , 2010 .

[32]  Rupinder Singh,et al.  Fused Deposition Modeling – A State of Art Review and Future Applications , 2014 .

[33]  Norman M. Wereley,et al.  Development and Testing of a Span-Extending Morphing Wing , 2011 .

[34]  Alessandro E. Pizzochero,et al.  Recent advances in active fiber composites for structural control , 2000, Smart Structures.

[35]  J. L. Leeuwen,et al.  How swifts control their glide performance with morphing wings , 2006, Nature.

[36]  Jayanth N. Kudva,et al.  Morphing aircraft concepts, classifications, and challenges , 2004, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[37]  I. Bond,et al.  Morphing skins , 2008, The Aeronautical Journal (1968).

[38]  A Hedenström,et al.  Gliding flight in a jackdaw: a wind tunnel study. , 2001, The Journal of experimental biology.

[39]  Darryll J. Pines,et al.  Design and Testing of a Pneumatic Telescopic Wing for Unmanned Aerial Vehicles , 2007 .

[40]  Ryan B. Wicker,et al.  3D Printing multifunctionality: structures with electronics , 2014 .

[41]  Gn Dayananda,et al.  Smart Aerodynamic Surface for a Typical Military Aircraft Using Shape Memory Elements , 2011 .

[42]  Manfred Morari,et al.  Aero-Structural Optimization of Morphing Airfoils for Adaptive Wings , 2011 .

[43]  Jukka Seppälä,et al.  Biodegradable and bioactive porous scaffold structures prepared using fused deposition modeling. , 2013, Journal of biomedical materials research. Part B, Applied biomaterials.

[44]  I. Gibson,et al.  Material properties and fabrication parameters in selective laser sintering process , 1997 .

[45]  A. F. Silva,et al.  Fused deposition modeling with polypropylene , 2015 .

[46]  S. Wang,et al.  Characterization of stainless steel parts by Laser Metal Deposition Shaping , 2014 .

[47]  James Mabe.  Variable area jet nozzle for noise reduction using shape memory alloy actuators , 2008 .

[48]  Guijun Bi,et al.  The effect of processing conditions on the mechanical properties of polyethylene produced by selective laser sintering , 2016 .

[49]  Jaret C. Riddick,et al.  Interfacial mechanical behavior of 3D printed ABS , 2016 .

[50]  Yanju Liu,et al.  Shape-memory polymers and their composites: Stimulus methods and applications , 2011 .

[51]  Robert A. Haynes,et al.  Towards the Development of a Span-wise Extending Unmanned Aerial System , 2020 .