Cavity Air Flow Behavior During Filling in Microinjection Molding

Process monitoring of microinjection molding (µ-IM) is of crucial importance in understanding the effects of different parameter settings on the process, especially on its performance and consistency with regard to parts' quality. Quality factors related to mold cavity air evacuation can provide valuable information about the process dynamics and also about the filling of a cavity by a polymer melt. In this paper, a novel experimental setup is proposed to monitor maximum air flow and air flow work as an integral of the air flow over time by employing a microelectromechanical system gas sensor mounted inside the mold. The influence of four µIM parameters, melt temperature, mold temperature, injection speed, and resistance to air evacuation, on two air flow-related output parameters is investigated by carrying out a design of experiment study. The results provide empirical evidences about the effects of process parameters on cavity air evacuation, and the influence of air evacuation on the part flow length.

[1]  Stefan Simeonov Dimov,et al.  A roadmapping study in Multi-Material Micro Manufacture , 2006 .

[2]  Suresh G. Advani,et al.  Use of genetic algorithms to optimize gate and vent locations for the resin transfer molding process , 1999 .

[3]  A. Liou,et al.  Injection molding of polymer micro- and sub-micron structures with high-aspect ratios , 2006 .

[4]  S. Dimov,et al.  The effects of tool surface quality in micro-injection moulding , 2007 .

[5]  H. N. Hansen,et al.  Study of process parameters effect on the filling phase of micro-injection moulding using weld lines as flow markers , 2010 .

[6]  S. Dimov,et al.  Investigation of micro-injection moulding: Factors affecting the replication quality , 2007 .

[7]  Wen-Bin Young,et al.  Effect of process parameters on injection compression molding of pickup lens , 2005 .

[8]  H Yokoi,et al.  Visualization analysis of flow front behavior during filling process of injection mold cavity by two-axis tracking system , 2002 .

[9]  Jer-Haur Chang,et al.  An experimental matrix design to optimize the weldline strength in injection molded parts , 2000 .

[10]  R. Zauner.  Micro powder injection moulding , 2006 .

[11]  Michael Sylvester Packianather,et al.  Micro-injection moulding: Factors affecting the achievable aspect ratios , 2007 .

[12]  Michael Sylvester Packianather,et al.  The finite element analysis of melt flow behaviour in micro-injection moulding , 2008 .

[13]  R. Wimberger-Friedl,et al.  Injection Molding of Sub-μm Grating Optical Elements , 2000 .

[14]  T. Kwon,et al.  Morphology and mechanical properties of injection molded articles with weld-lines , 1997 .

[15]  J. Horlock,et al.  Engineering Thermodynamics , 1958, Nature.

[16]  Roberto Spina,et al.  Experimental and numerical analysis of metal injection molded products , 2005 .

[17]  Jürgen Fleischer,et al.  The manufacturing of micro molds by conventional and energy-assisted processes , 2007 .

[18]  J. Giboz,et al.  Microinjection molding of thermoplastic polymers: a review , 2007 .

[19]  M. Kuittinen,et al.  Transparent thermoplastics: Replication of diffractive optical elements using micro-injection molding , 2007 .

[20]  G. Menges,et al.  How to make injection molds , 1987 .

[21]  Stefan Simeonov Dimov,et al.  Editorial for the special issue of IJAMT on multi material microsystem manufacturing , 2007 .

[22]  Abdelhakim Bendada,et al.  Analysis of thermal contact resistance between polymer and mold in injection molding , 2004 .

[23]  Guido Tosello,et al.  Precision moulding of polymer micro components: Optimization, Simulation, Tooling, Quality Control and Multi-Material Application , 2008 .

[24]  Yung Kang Shen,et al.  Analysis for microstructure of microlens arrays on micro-injection molding by numerical simulation , 2008 .

[25]  Rong-Yeu Chang,et al.  Modifying the tait equation with cooling‐rate effects to predict the pressure–volume–temperature behaviors of amorphous polymers: Modeling and experiments , 1996 .

[26]  Duc Truong Pham,et al.  Some recent advances in multi-material micro- and nano-manufacturing , 2010 .

[27]  W. Michaeli,et al.  Micro assembly injection moulding for the generation of hybrid microstructures , 2003 .

[28]  Frederick R. Phelan,et al.  Simulation of the injection process in resin transfer molding , 1997 .

[29]  Byung Kim,et al.  Scaling Issues in Miniaturization of Injection Molded Parts , 2004 .

[30]  Patricia Krawczak,et al.  Weld‐line sensitivity of injected amorphous polymers , 2004 .

[31]  Sybil P. Parker.  McGraw-Hill dictionary of engineering , 1984 .

[32]  A. Haufe,et al.  Computer simulation of weld lines in injection molded poly(methyl methacrylate) , 1996 .

[33]  J. Hausselt,et al.  Injection molding of microstructured components from plastics, metals and ceramics , 2002 .

[34]  Jatan P. Shah,et al.  Implementation and analysis of polymeric microstructure replication by micro injection molding , 2004 .

[35]  N. P. Hung,et al.  Development of Microreplication Process—Micromolding , 2003 .

[36]  V. Piotter,et al.  Performance and simulation of thermoplastic micro injection molding , 2002 .

[37]  Simualtion of the Micro Injection Molding Process , 2001 .

[38]  X. Han,et al.  Effects of molding conditions on transcription molding of microscale prism patterns using ultra-high-speed injection molding , 2006 .

[39]  Cheng-Hsien Wu,et al.  Effects of geometry and injection‐molding parameters on weld‐line strength , 2005 .