Performance of suspended finned heat pipes in high-temperature latent heat thermal energy storage

This study presents a thermal network model for evaluating heat transfer enhancement in a high-temperature latent heat storage unit incorporating finned heat pipes. The objective of this heat enhanced latent heat storage system was to improve the thermal performance of concentrating solar power plants. In this proposed design, finned heat pipes are used in the heat storage unit as effective heat spreaders. The finned heat pipes are kept in suspension and are adjacent to the heat transfer channel in order to increase the overall heat conductance of the phase change material (PCM). The feasibility of the proposed design was established by conducting experimental measurements of the solidification process. The results have shown that the performance was significantly improved by adding finned heat pipes, especially at the later stage of PCM solidification. The performance enhancement was quantified based on heat pipe effectiveness. It was found that the effectiveness of the twelve-heat pipe configuration reached 2.4 after 5 h of simulated operation. In addition, a preliminary system sizing was conducted in order to estimate the system size required for 50 MW electrical power output.

[1]  T. L. Bergman,et al.  High temperature latent heat thermal energy storage using heat pipes , 2010 .

[2]  Kamal Abdel Radi Ismail,et al.  Experimentally validated two dimensional numerical model for the solidification of PCM along a horizontal long tube , 2014 .

[3]  D. Mills.  Advances in solar thermal electricity technology , 2004 .

[4]  Hugh W. Coleman,et al.  Experimentation, Validation, and Uncertainty Analysis for Engineers , 2009 .

[5]  A. Akbarzadeh,et al.  A numerical and experimental study of solidification around axially finned heat pipes for high temperature latent heat thermal energy storage units , 2014 .

[6]  S. D. Pohekar,et al.  Performance enhancement in latent heat thermal storage system: A review , 2009 .

[7]  Amir Faghri,et al.  A network thermodynamic analysis of the heat pipe , 1998 .

[8]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[9]  Doerte Laing,et al.  High-Temperature Solid-Media Thermal Energy Storage for Solar Thermal Power Plants , 2012, Proceedings of the IEEE.

[10]  Ulf Herrmann,et al.  Two-tank molten salt storage for parabolic trough solar power plants , 2004 .

[11]  D. Williams,et al.  Assessment of Candidate Molten Salt Coolants for the NGNP/NHI Heat-Transfer Loop , 2006 .

[12]  Yan Wang,et al.  Thermal analysis and design of solid energy storage systems using a modified lumped capacitance method. , 2015 .

[13]  J. W. Ramsey,et al.  Freezing on a finned tube for either conduction-controlled or natural-convection-controlled heat transfer , 1981 .

[14]  Marcia B. H. Mantelli,et al.  Performance of naphthalene thermosyphons with non-condensable gases – Theoretical study and comparison with data , 2010 .

[15]  T. L. Bergman,et al.  Enhancement of latent heat energy storage using embedded heat pipes , 2011 .

[16]  Amir Faghri,et al.  Heat Pipe Science And Technology , 1995 .

[17]  S. Patankar.  Numerical Heat Transfer and Fluid Flow , 2018, Lecture Notes in Mechanical Engineering.

[18]  S. M. Hasnain.  Review on sustainable thermal energy storage technologies, Part I: heat storage materials and techniques , 1998 .

[19]  J. Mason,et al.  The technical, geographical, and economic feasibility for solar energy to supply the energy needs of the US , 2009 .

[20]  William G. Anderson.  Intermediate Temperature Fluids for Heat Pipes and Loop Heat Pipes , 2007 .

[21]  R. Pitchumani,et al.  Analysis and optimization of a latent thermal energy storage system with embedded heat pipes , 2011 .

[22]  Chao Xu,et al.  Performance analysis of a two-stage thermal energy storage system using concrete and steam accumulator , 2011 .

[23]  T. L. Bergman,et al.  Economic evaluation of latent heat thermal energy storage using embedded thermosyphons for concentrating solar power applications , 2011 .

[24]  Thomas Bauer,et al.  Approximate analytical solutions for the solidification of PCMs in fin geometries using effective thermophysical properties , 2011 .