Evaluation of microstructural changes by X-ray diffraction peak profile and focused ion beam/scanning ion microscope analysis

[1]  Domenico Umbrello,et al.  Analysis of the white layers formed during machining of hardened AISI 52100 steel under dry and cryogenic cooling conditions , 2013 .

[2]  I. S. Jawahir,et al.  Effects of cryogenic cooling on surface layer alterations in machining of AISI 52100 steels , 2012 .

[3]  Domenico Umbrello,et al.  Experimental analysis of mechanisms related to white layer formation during hard turning of AISI 52100 bearing steel , 2012 .

[4]  L. Settineri,et al.  Dry and Cryogenic Machining: Comparison from the Sustainability Perspective , 2012 .

[5]  D. Umbrello,et al.  The effects of cryogenic cooling on surface integrity in hard machining: A comparison with dry machining , 2011 .

[6]  D. Mikkola,et al.  Employing X-ray scattering to characterize materials with grain sizes in the nano-regime , 2008, Powder Diffraction.

[7]  Shreyes N. Melkote,et al.  Modeling of white layer formation under thermally dominant conditions in orthogonal machining of hardened AISI 52100 steel , 2008 .

[8]  J. Gubicza,et al.  Characterization of defect structures in nanocrystalline materials by X-ray line profile analysis , 2007 .

[9]  Yuebin Guo,et al.  The influence of machining induced residual stress and phase transformation on the measurement of subsurface mechanical behavior using nanoindentation , 2006 .

[10]  Shreyes N. Melkote,et al.  Analysis of white layers formed in hard turning of AISI 52100 steel , 2005 .

[11]  Tamás Ungár,et al.  Correlation between strength and microstructure of ball-milled Al–Mg alloys determined by X-ray diffraction , 2004 .

[12]  T. Ungár.  Microstructural parameters from X-ray diffraction peak broadening , 2004 .

[13]  Yuebin Guo,et al.  A comparative study of hard turned and cylindrically ground white layers , 2004 .

[14]  R. Ghosh,et al.  Investigation of White Layers Formed in Conventional and Cryogenic Hard Turning of Steels , 2003 .

[15]  Gerry Byrne,et al.  TEM study on the surface white layer in two turned hardened steels , 2002 .

[16]  Jiajun Liu,et al.  Tribo-metallographic behavior of high carbon steels in dry sliding: III. Dynamic microstructural changes and wear , 1999 .

[17]  Christopher J. Evans,et al.  White Layers and Thermal Modeling of Hard Turned Surfaces , 1997, Manufacturing Science and Engineering: Volume 2.

[18]  W. Konig,et al.  Machining hard materials with geometrically defined cutting edges , 1990 .

[19]  S. A. Howard,et al.  Profile fitting of powder diffraction patterns , 1989 .

[20]  B. J. Griffiths,et al.  White Layer Formations at Machined Surfaces and Their Relationship to White Layer Formations at Worn Surfaces , 1985 .

[21]  A. Vaars,et al.  A method to eliminate the background in X-ray diffraction patterns of oriented clay mineral samples , 1981, Clay Minerals.

[22]  B. Warren.  X-ray studies of deformed metals , 1959 .

[23]  Gustaf Arrhenius,et al.  X-ray diffraction procedures for polycrystalline and amorphous materials , 1955 .

[24]  P. Scherrer,et al.  Bestimmung der Größe und der inneren Struktur von Kolloidteilchen mittels Röntgenstrahlen , 1918 .