Thermo-mechanical response of superalloy honeycomb sandwich panels subjected to non-steady thermal loading

Abstract This paper investigates heat-shielding performance and 3D thermal deformation behavior of two superalloy honeycomb-core sandwich panels in time-varying thermal environment by using a self-developed transient aerodynamic heating simulation system and a novel active imaging stereo-digital image correlation (stereo-DIC) technique. To facilitate deformation measurement of large objects using stereo-DIC, a simple but practical technique is adopted for fabricating high-temperature speckle patterns on large measuring areas. The results indicate that the sandwich panels provide good thermal shielding performance under 900 °C with the thermal insulation effect stabilizing at around 30%. The measured high-temperature deformation fields of the test sandwich panels reveal that an in-plane homogeneous thermal expansion occurs as expected, while the out-of-plane deformation shows evident axisymmetric distributions with the maximum deflections dependent on the temperature differences between the back and front facets. The results provide a foundational understanding on the thermal–mechanical characteristics of superalloy honeycomb-core sandwich panels, which is essential to the structural design of a superalloy honeycomb sandwich thermal protection system.

[1]  Liviu Librescu,et al.  Advances in the Structural Modeling of Elastic Sandwich Panels , 2004 .

[2]  A. Evans,et al.  Optimization of Thermal Protection Systems Utilizing Sandwich Structures with Low Coefficient of Thermal Expansion Lattice Hot Faces , 2011 .

[3]  Helena Pereira,et al.  Mechanical behavior of multilayered sandwich panels of wood veneer and a core of cork agglomerates , 2015 .

[4]  Jianchun Li,et al.  A coupled thermo-mechanical discontinuum model for simulating rock cracking induced by temperature stresses , 2015 .

[5]  A. Asundi,et al.  Digital image correlation using iterative least squares and pointwise least squares for displacement field and strain field measurements , 2009 .

[6]  William L. Ko.  Mechanical and thermal buckling analysis of sandwich panels under different edge conditions , 1993 .

[7]  N. Alghamdi,et al.  Bending Analysis of Functionally Graded Sandwich Plates Under the Effect of Mechanical and Thermal Loads , 2010 .

[8]  D. Fang,et al.  Fabrication and heat transfer characteristics of C/SiC pyramidal core lattice sandwich panel , 2015 .

[9]  Guoyin Zu,et al.  Performance of aluminum foam–steel panel sandwich composites subjected to blast loading , 2013 .

[10]  K. Kang,et al.  A composite sandwich panel integrally woven with truss core , 2015 .

[11]  Yong Xia,et al.  High-temperature digital image correlation method for full-field deformation measurement at 1200 °C , 2010 .

[12]  Anand Asundi,et al.  Measurement of coefficient of thermal expansion of films using digital image correlation method , 2009 .

[13]  D. Paul,et al.  History of Flight Vehicle Structures 1903-1990 , 2004 .

[14]  Chenguang Huang,et al.  Experimental Investigation on Thermal Buckling Behavior of Truss-Core Sandwich Panels , 2015 .

[15]  E. Reissner,et al.  Finite Deflections of Sandwich Plates , 1948 .

[16]  John T. Dorsey,et al.  Advanced Metallic Thermal Protection System Development , 2002 .

[17]  F. Lam,et al.  Stiffness and strength of oil palm wood core sandwich panel under center point bending , 2015 .

[18]  In-plane compression response of wire-woven metal cored sandwich panels , 2014 .

[19]  Genevieve Langdon,et al.  Large inelastic response of unbonded metallic foam and honeycomb core sandwich panels to blast loading , 2010 .

[20]  Charles Libove,et al.  A general small-deflection theory for flat sandwich plates , 1948 .

[21]  A. Waas,et al.  Response of Actively Cooled Metal Foam Sandwich Panels Exposed to Thermal Loading , 2007 .

[22]  Anand Asundi,et al.  Two-dimensional digital image correlation for in-plane displacement and strain measurement: a review , 2009 .

[23]  Bing Sun,et al.  Experimental investigation and numerical simulation of heat-transfer properties of metallic honeycomb core structure up to 900 °C , 2013 .

[24]  Raphael T. Haftka,et al.  (Student Paper) Analysis and Design of Corrugated-Core Sandwich Panels for Thermal Protection Systems of Space Vehicles , 2006 .

[25]  A. Pandey,et al.  Thermomechanical Behavior of Developmental Thermal Barrier Coating Bond Coats , 2013 .

[26]  N. Fleck,et al.  The out-of-plane compressive behaviour of woven-core sandwich plates , 2004 .

[27]  Guoxing Lu,et al.  Deformation and failure of blast-loaded metallic sandwich panels: experimental investigations , 2008 .

[28]  Erasmo Carrera,et al.  A Survey With Numerical Assessment of Classical and Refined Theories for the Analysis of Sandwich Plates , 2009 .

[29]  W. Lance Richards,et al.  Titanium honeycomb panel testing , 1991 .

[30]  Wang Yuewu,et al.  Experimental research on the ultimate strength of hard aluminium alloy 2017 subjected to short-time radioactive heating , 2012 .

[31]  Liping Yu,et al.  Optimization of a three-dimensional digital image correlation system for deformation measurements in extreme environments. , 2012, Applied optics.

[32]  Lishe Dong.  STEADY THERMAL PERFORMANCE OF METALLIC HONEYCOMB PANELS , 2008 .

[33]  W. Ko.  Heat Shielding Characteristics and Thermostructural Performance of a Superalloy Honeycomb Sandwich Thermal Protection System (TPS) , 2004 .

[34]  Ole Thybo Thomsen,et al.  Thermal Buckling and Postbuckling of Sandwich Panels with a Transversely Flexible Core , 2008 .

[35]  M. G. Lee,et al.  Bending response of sandwich panels with discontinuous wire-woven metal cores , 2014 .

[36]  A. Waas,et al.  Thermal buckling of metal foam sandwich panels for convective thermal protection systems , 2005 .

[37]  A. Pandey,et al.  Temperature Dependence of the Anisotropy and Creep in a Single-Crystal Nickel Superalloy , 2015 .