Investigation of ejector-equipped Joule–Thomson refrigerator operating below 77 K

Abstract The lowest attainable refrigeration temperature of a nitrogen based Joule–Thomson refrigerator is generally limited to 77 K since the compressor suction pressure is usually higher than atmospheric pressure. The Joule–Thomson process with an ejector is proposed to achieve a refrigeration temperature as low as 68 K by adjusting the evaporation pressure down to 28 kPa and boosting the return stream pressure up to 147 kPa. A one-dimensional numerical model is developed to predict the performance of the ejector at cryogenic temperature, and its accuracy is compared with experimental data. The analysis results show that the addition of the ejector in the Joule–Thomson refrigeration cycle increases up to 5 times the overall efficiency, where the maximum achievable COP and exergy efficiency are 0.0195 and 6.65%, respectively. Other featured advantages of the proposed Joule–Thomson refrigeration cycle with ejector are the simplicity of cycle, minimization of mechanical moving components, cost effectiveness, and high reliability compared to other cryogenic refrigeration methods using pumps or cold compressors in Joule–Thomson cycles.

[1]  Bin-Juine Huang,et al.  A 1-D analysis of ejector performance , 1999 .

[2]  Y. Çengel,et al.  Thermodynamics : An Engineering Approach , 1989 .

[3]  Bin-Juine Huang,et al.  Empirical correlation for ejector design , 1999 .

[4]  M. McLinden,et al.  NIST Standard Reference Database 23: Reference Fluid Thermodynamic and Transport Properties-REFPROP, Version 8.0 , 2007 .

[5]  H. Kursad Ersoy,et al.  Performance characteristics of ejector expander transcritical CO2 refrigeration cycle , 2012 .

[6]  Fabio Inzoli,et al.  A study of working fluids for heat driven ejector refrigeration using lumped parameter models , 2015 .

[7]  Wenjian Cai,et al.  Shock circle model for ejector performance evaluation , 2007 .

[8]  Souvik Bhattacharyya,et al.  Thermodynamic design and simulation of a CO2 based transcritical vapour compression refrigeration system with an ejector , 2014 .

[9]  Björn Palm,et al.  Parametric analysis of ejector working characteristics in the refrigeration system , 2014 .

[10]  J. Keenan,et al.  An Investigation of Ejector Design by Analysis and Experiment , 1950 .

[11]  G. Venkatarathnam.  Cryogenic mixed refrigerant processes , 2008 .

[12]  Paolo Chiesa,et al.  An Integrated Lumped Parameter-CFD approach for off-design ejector performance evaluation , 2015 .

[13]  Predrag Stojan Hrnjak,et al.  Experimental validation of a prototype ejector designed to reduce throttling losses encountered in transcritical R744 system operation , 2008 .

[14]  Sangkwon Jeong,et al.  Investigation of neon–nitrogen mixed refrigerant Joule–Thomson cryocooler operating below 70 K with precooling at 100 K , 2014 .

[15]  Jean-Marie Seynhaeve,et al.  CFD analysis of a supersonic air ejector. Part I: Experimental validation of single-phase and two-phase operation , 2009 .

[16]  Bogdan Diaconu,et al.  Numerical assessment of steam ejector efficiencies using CFD , 2009 .

[17]  Jianlin Yu,et al.  Improving the performance of small Joule–Thomson cryocooler , 2008 .

[18]  H. Olivier,et al.  Behavior of shock trains in a diverging duct , 2010 .

[19]  Eckhard A. Groll,et al.  Study of ejector efficiencies in refrigeration cycles , 2013 .

[20]  Yann Bartosiewicz,et al.  Optical validation of ejector flow characteristics predicted by computational analysis , 2012 .

[21]  David F. Bagster,et al.  A New Ejector Theory Applied to Steam Jet Refrigeration , 1977 .

[22]  Yann Bartosiewicz,et al.  Numerical and Experimental Investigations on Supersonic Ejectors , 2005 .

[23]  A. M. Arkharov,et al.  Analysis of existing small-capacity plants for natural-gas liquefaction , 2010 .