Thermal model validation of plate heat exchangers with generalized configurations

Thermal models of plate heat exchangers rely on correlations for the evaluation of the convective heat transfer coefficients inside the channels. It is usual to configure the exchanger with one countercurrent single-pass arrangement for acquiring heat transfer experimental data. This type of configuration approaches the ideal case of pure countercurrent flow conditions, and therefore a simplified mathematical model can be used for parameter estimation. However, it is known that the results of parameter estimation depend on the selected exchanger configuration because the effects of flow maldistribution inside its channels are incorporated into the heat transfer coefficients. This work presents a parameter estimation procedure for plate heat exchangers that handles experimental data from multiple configurations. The procedure is tested with an Armfield FT-43 heat exchanger with flat plates and the parameter estimation results are compared to those obtained from the usual method of single-pass arrangements. It can be observed that the heat transfer correlations obtained for plate heat exchangers are intimately associated with the configuration(s) experimentally tested and the corresponding flow distribution pattern(s).

[1]  L. P. Pertsev.  Design of plate heat exchangers , 1968 .

[2]  Bernard Thonon,et al.  Les échangeurs à plaques: dix ans de recherche au GRETh: Partie 2. Dimensionnement et mauvaise distribution , 1996 .

[3]  R. Shah,et al.  Handbook of single-phase convective heat transfer , 1987 .

[4]  R. A. Mashelkar,et al.  Heat Transfer Equipment Design , 1988 .

[5]  A. B. Jarzebski,et al.  Dimensioning of plate heat exchangers to give mininum annual operating costs , 1985 .

[6]  Jorge Andrey Wilhelms Gut,et al.  Selecting Optimal Configurations for Multisection Plate Heat Exchangers in Pasteurization Processes , 2003 .

[7]  GMaskill Smith,et al.  The chemical engineer , 1946 .

[8]  M. Andrade,et al.  An algorithm for steady-state simulation of plate heat exchangers , 2002 .

[9]  Tadeusz Zaleski,et al.  Plate heat exchangers—method of calculation, charts and guidelines for selecting plate heat exchanger configurations , 1992 .

[10]  R. Shah,et al.  Multipass plate heat exchangers -- Effectiveness-NTU results and guidelines for selecting pass arrangements , 1989 .

[11]  Sarit K. Das,et al.  Effect of flow distribution to the channels on the thermal performance of a plate heat exchanger , 2002 .

[12]  W. Rohsenow,et al.  Handbook of Heat Transfer , 1998 .

[13]  R. M. Manglik,et al.  Enhanced Heat Transfer Characteristics of Viscous Liquid Flows in a Chevron Plate Heat Exchanger , 1999 .

[14]  P. J. Heggs,et al.  Rating calculation for plate heat exchanger effectiveness and pressure drop using existing performance data , 2002 .

[15]  Jorge Andrey Wilhelms Gut,et al.  Modeling of plate heat exchangers with generalized configurations , 2003 .

[16]  Pablo Ignacio Tamborenea,et al.  Thermal effectiveness of multipass plate exchangers , 1988 .

[17]  H. Müller-Steinhagen,et al.  Comparison of Crystallization Fouling in Plate and Double-Pipe Heat Exchangers , 2001 .

[18]  Jorge Andrey Wilhelms Gut,et al.  Optimal configuration design for plate heat exchangers , 2004 .

[19]  Bernard Thonon,et al.  Cashier applicationLes échangeurs à plaques: dix ans de recherche au GRETh: Partie 2. Dimensionnement et mauvaise distributionPlate heat exchangers: ten years of research at GRETh: Part 2. Sizing and flow maldistribution , 1996 .

[20]  Ralph A. Buonopane,et al.  A study of the effects of internal rib and channel geometry in rectangular channels. Part I. Pressure drop , 1969 .

[21]  Tadeusz Zaleski,et al.  Approximate method of solving equations for plate heat exchangers , 1992 .

[22]  J. E. O'Brien,et al.  Low Reynolds number flow heat exchangers: Eds. S. Kakac, R. K. Shah and A. E. Bergles , 1984 .

[23]  H. Martin,et al.  Flow distribution and pressure drop in plate heat exchangers—II Z-type arrangement , 1984 .

[24]  C. Bennett,et al.  Momentum, Heat, and Mass Transfer , 1962 .