Optimization of Variable-Capacitance Micromotor Using Genetic Algorithm

In this paper, the optimization shape of a polysilicon variable-capacitance micromotor (VCM) was determined using genetic algorithm (GA). The optimum goal of the algorithm was found for a maximum torque value and a minimum torque ripple, following changing the geometric parameters. The optimization process was carried out using a combination of GA and finite-element method (FEM). The fitness value was calculated by FEM analysis using COMSOL3.4, and the GA was realized by MATLAB7.4. The proposed method has been applied for the two case studies, and it has been also compared with successive sampling method. The results show that the optimized micromotor using GA had a higher torque value and a lower torque ripple, indicating the validity of this methodology for VCM design.

[1]  Wallace S. H. Wong,et al.  An explicit drive algorithm for aiding the design of firing sequence in side-drive micromotor , 2008 .

[2]  M. Rossi,et al.  A new FEM approach for field and torque simulation of electrostatic microactuators , 2002 .

[3]  P. Di Barba,et al.  3-D computer aided analysis of the "Berkeley" electrostatic micromotor , 1995 .

[4]  R. Ghodssi,et al.  Design, Fabrication, and Characterization of a Rotary Micromotor Supported on Microball Bearings , 2008, Journal of Microelectromechanical Systems.

[5]  Jeffrey H. Lang,et al.  Dynamic characterization of a linear electrostatic micromotor supported on microball bearings , 2007 .

[6]  Kay Hameyer,et al.  Optimization of radial active magnetic bearings using the finite element technique and the differential evolution algorithm , 2000 .

[7]  A. Emadi,et al.  Micromachines: principles of operation, dynamics, and control , 2005, IEEE International Conference on Electric Machines and Drives, 2005..

[8]  Abolfazl Vahedi,et al.  Minimizing the torque ripple of variable capacitance electrostatic micromotors , 2006 .

[9]  Yu-Chong Tai,et al.  IC-processed electrostatic micro-motors , 1988, Technical Digest., International Electron Devices Meeting.

[10]  R. Belmans,et al.  Technique for finding the optimum geometry of electrostatic micromotors , 1993, Conference Record of the 1993 IEEE Industry Applications Conference Twenty-Eighth IAS Annual Meeting.

[11]  Zhang Wen ELECTROSTATIC MICROMOTOR AND ITS RELIABILITY , 2005 .

[12]  R. Ghodssi,et al.  An electric induction micromotor , 2005, Journal of Microelectromechanical Systems.

[13]  Jeffrey H. Lang,et al.  A six-phase multilevel inverter for MEMS electrostatic induction micromotors , 2004, IEEE Transactions on Circuits and Systems II: Express Briefs.

[14]  L. Schumaker Spline Functions: Basic Theory , 1981 .

[15]  Yi-Sheng Zhou,et al.  Optimal design for fuzzy controllers by genetic algorithms , 2000 .

[16]  Zbigniew Michalewicz,et al.  Genetic Algorithms + Data Structures = Evolution Programs , 1992, Artificial Intelligence.

[17]  J. Lang,et al.  Electric micromotor dynamics , 1992 .

[18]  Abolfazl Vahedi,et al.  Study the influence of geometric parameters on the torque of electrostatic micromotors , 2006 .

[19]  Douglas H. Werner,et al.  Genetic Algorithms in Electromagnetics , 2007 .

[20]  A. J. Sangster,et al.  Determination of the forces present in an electrostatic micromotor , 1993 .

[21]  A. Hamler,et al.  Analysis of iron loss in interior permanent magnet synchronous motor over a wide-speed range of constant output power operation , 2000 .

[22]  Abolfazl Vahedi,et al.  Analysis and Optimization of MEMS Electrostatic Microactuator , 2007 .