Effective decapsulation of copper wire-bonded microelectronic devices for reliability assessment

Abstract The wire bonding industry has made a major shift in wire materials from gold to copper, primarily due to cost concerns. Copper wire-bonds are now present in many commercial off-the-shelf (COTS) devices but minimally used in automotive, industrial, or military-grade applications due to lack of detailed understanding about reliability concerns. A thorough study of wire bond reliability includes performing bond shear and pull strength measurements before and after stress testing. This in turn requires a special decapsulation procedure for copper wire-bonded devices because, unlike gold, copper is chemically potent. Many techniques for copper wire-bonded device decapsulation exist and can be categorized into laser-, plasma-, and acid-based processes. This paper reviews some of these techniques and discusses the decapsulation mechanism, which involves decomposition of the epoxy resin. By understanding the decapsulation mechanism and available techniques, a unique decapsulation method was developed. The effectiveness of this method is presented along with scanning electron microscopy (SEM) images of the results, which indicate minimal etching of copper wire bonds. The critical parameters of this technique are also identified, a suitable range of input for each parameter is analyzed theoretically, and a design of experiment (DOE) is conducted to find optimal values for each parameter. Several SEM images are provided to show both the good and bad results from the DOE. An image method for measuring effectiveness of decapsulation is also presented.

[1]  Patrick McCluskey,et al.  Decapsulation of Plastic Encapsulated Microelectronics with Copper Wire Bonds , 2016 .

[2]  E. Mengotti,et al.  Eliminating infant mortality in metallized film capacitors by defect detection , 2014, Microelectron. Reliab..

[3]  Subramani Manoharan,et al.  Failure mechanisms in encapsulated copper wire-bonded devices , 2016, 2016 IEEE 23rd International Symposium on the Physical and Failure Analysis of Integrated Circuits (IPFA).

[4]  Patrick McCluskey,et al.  Advancements in Silver Wire Bonding , 2017 .

[5]  Copper ball bond shear test for two pad aluminum thicknesses , 2014, 2014 IEEE 16th Electronics Packaging Technology Conference (EPTC).

[6]  Mohd Ambar Yarmo,et al.  Corrosion study at Cu–Al interface in microelectronics packaging , 2002 .

[7]  G. Q. Zhang,et al.  Decapsulation methods for Cu interconnection packages , 2012, 2012 13th International Conference on Electronic Packaging Technology & High Density Packaging.

[8]  B. Vandevelde,et al.  Early fatigue failures in copper wire bonds inside packages with low CTE green mold compounds , 2012, 2012 4th Electronic System-Integration Technology Conference.

[9]  F. McCluskey,et al.  Reliability and failure analysis of Cu-Sn transient liquid phase sintered (TLPS) joints under power cycling loads , 2015, 2015 IEEE 3rd Workshop on Wide Bandgap Power Devices and Applications (WiPDA).

[10]  Diganta Das,et al.  Critical review of U.S. Military environmental stress screening (ESS) handbook , 2016, 2016 IEEE Accelerated Stress Testing & Reliability Conference (ASTR).

[11]  G. Harman.  Wire Bonding in Microelectronics: Materials, Processes, Reliability, and Yield , 1997 .

[12]  N. Srikanth,et al.  Acid Decapsulation of Epoxy Molded IC Packages With Copper Wire Bonds , 2006, IEEE Transactions on Electronics Packaging Manufacturing.

[13]  F. McCluskey,et al.  Strength and Reliability of High Temperature Transient Liquid Phase Sintered Joints , 2014 .

[14]  Huang Guojun.  Comparison of copper, silver and gold wire bonding on interconnect metallization , 2012 .

[15]  Michael Pecht,et al.  Encapsulation Technologies for Electronic Applications , 2019 .