Numerical and experimental analysis of unidirectional meander-line coil electromagnetic acoustic transducers

The elastic waves generated by traditional meander- line coil electromagnetic acoustic transducers (EMATs) propagate in two directions, overlapping the echo signals from defects with the same distances, and the defect echo signal is hard to distinguish from the edge-reflected signal when the EMATs are near the edge of a specimen. In this paper, a unidirectional EMAT with two meander-line coils is proposed. A finite element model is used to simulate the directivity of the Rayleigh and shear vertical waves generated by these EMATs. Six transducers are fabricated using the printed circuit technique. The unidirectional Rayleigh wave and shear vertical wave are tested, and the results agree well with the simulation.

[1]  H. Ogi,et al.  EMATs for Science and Industry: Noncontacting Ultrasonic Measurements , 2010 .

[2]  R. B. Thompson.  Physical Principles of Measurements with EMAT Transducers , 1990 .

[3]  P. Nagy,et al.  The impact of magnetostriction on the transduction of normal bias field EMATs , 2012 .

[4]  Krishnan Balasubramaniam,et al.  A two-stage finite element model of a meander coil electromagnetic acoustic transducer transmitter , 2011 .

[5]  Bernhard R. Tittmann,et al.  Finite element analysis of coupled electromagnetic acoustic systems , 1999 .

[6]  Reinhold Ludwig,et al.  Numerical simulation of electromagnetic acoustic transducer in the time domain , 1991 .

[7]  Krishnan Balasubramaniam,et al.  A hybrid finite element model for simulation of electromagnetic acoustic transducer (EMAT) based plate waves , 2010 .

[8]  Peter Cawley,et al.  Quantitative modeling of the transduction of electromagnetic acoustic transducers operating on ferromagnetic media , 2010, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[9]  Francisco Hernandez-Valle,et al.  Initial tests for designing a high temperature EMAT with pulsed electromagnet , 2010 .

[10]  R. Ludwig,et al.  Numerical simulations of an electromagnetic acoustic transducer-receiver system for NDT applications , 1993 .

[11]  H. Ogi.  Field dependence of coupling efficiency between electromagnetic field and ultrasonic bulk waves , 1997 .

[12]  Peter Cawley,et al.  Study and comparison of different EMAT configurations for SH wave inspection , 2011, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[13]  Lei Kang,et al.  3-D modeling and analysis of meander-line-coil surface wave EMATs , 2012 .

[14]  S B Palmer,et al.  High accuracy non-contact ultrasonic thickness gauging of aluminium sheet using electromagnetic acoustic transducers. , 2001, Ultrasonics.

[15]  J.L. Rose,et al.  Lamb wave generation and reception with time-delay periodic linear arrays: a BEM simulation and experimental study , 1999, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[16]  R.B. Thompson,et al.  A Model for the Electromagnetic Generation and Detection of Rayleigh and Lamb Waves , 1973, IEEE Transactions on Sonics and Ultrasonics.

[17]  H. Ogi,et al.  Line-focusing electromagnetic acoustic transducers for the detection of slit defects , 1999, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[18]  Hirotsugu Ogi,et al.  Line-focusing of ultrasonic SV wave by electromagnetic acoustic transducer , 1998 .

[19]  R.B. Thompson,et al.  A model for the electromagnetic generation of ultrasonic guided waves in ferromagnetic metal polycrystals , 1978, IEEE Transactions on Sonics and Ultrasonics.

[20]  Peter Cawley,et al.  Long range propagation of Lamb waves in chemical plant pipework , 1997 .

[21]  Masahiko Hirao,et al.  Arrayed-Coil EMAT for Longitudinal Wave in Steel Wires. , 1999 .

[22]  C. M. Fortunko,et al.  The design and use of electromagnetic acoustic wave transducers (EMATs) , 1983 .

[23]  K. Grattan,et al.  A model for pulsed Rayleigh wave and optimal EMAT design , 2006 .