Forming characteristics and mechanism of variable polarity TIG-based wire arc additive manufacturing of Al–Mg-Zn-Cu alloy

[1]  Chendong Shao,et al.  Effect of Molten Pool Behaviors on Welding Defects in Tandem Ng-Gmaw Based on Cfd Simulation , 2022, SSRN Electronic Journal.

[2]  Dae-Won Cho,et al.  CFD simulation of molten pool dynamic behavior on vertical-downward position in P-GMAW process , 2022, International Communications in Heat and Mass Transfer.

[3]  W. Cho,et al.  Analysis of molten pool dynamics in laser welding with beam oscillation and filler wire feeding , 2021 .

[4]  Rui Fu,et al.  Hot-wire arc additive manufacturing of aluminum alloy with reduced porosity and high deposition rate , 2020 .

[5]  Chunli Yang,et al.  Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties , 2020 .

[6]  F. Jiang,et al.  Anisotropic mechanical properties and deformation behavior of low-carbon high-strength steel component fabricated by wire and arc additive manufacturing , 2020, Materials Science and Engineering: A.

[7]  H. Biermann,et al.  Electron beam welding of CrMnNi-steels: CFD-modeling with temperature sensitive thermophysical properties , 2019, International Journal of Heat and Mass Transfer.

[8]  Chunli Yang,et al.  The effects of double groove type on the backing weld penetration in swing arc vertical-up MAG welding , 2019, Welding in the World.

[9]  Chunli Yang,et al.  Effects of post-deposition heat treatment on microstructures of GTA-additive manufactured 2219-Al , 2019, Science and Technology of Welding and Joining.

[10]  B. Cong,et al.  Microstructure and mechanical properties of wire + arc additively manufactured Al-Mg-Si aluminum alloy , 2018, Materials Letters.

[11]  Cheolhee Kim,et al.  A study on transient flow characteristic in friction stir welding with real-time interface tracking by direct surface calculation , 2018 .

[12]  Bojin Qi,et al.  Microstructure and mechanical properties of double-wire + arc additively manufactured Al-Cu-Mg alloys , 2018 .

[13]  Chenglei Diao,et al.  Numerical analysis of heat transfer and fluid flow in multilayer deposition of PAW-based wire and arc additive manufacturing , 2018, International Journal of Heat and Mass Transfer.

[14]  Imre Horváth,et al.  A layers-overlapping strategy for robotic wire and arc additive manufacturing of multi-layer multi-bead components with homogeneous layers , 2018 .

[15]  Ming Gao,et al.  Wire arc additive manufacturing of Al-6Mg alloy using variable polarity cold metal transfer arc as power source , 2018 .

[16]  D. Gu,et al.  Selective laser melting additive manufacturing of in situ Al2Si4O10/Al composites: Microstructural characteristics and mechanical properties , 2017 .

[17]  Chunli Yang,et al.  Mechanical properties of 2219-Al components produced by additive manufacturing with TIG , 2016 .

[18]  Suck-Joo Na,et al.  CFD based visualization of the finger shaped evolution in the gas metal arc welding process , 2016 .

[19]  J. Gu,et al.  The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy , 2016 .

[20]  Huijun Li,et al.  A practical path planning methodology for wire and arc additive manufacturing of thin-walled structures , 2015 .

[21]  Jialuo Ding,et al.  Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy , 2015 .

[22]  M. Brochu,et al.  Solid freeform fabrication of Al–Si components via the CSC-MIG process , 2012 .

[23]  Paul A. Colegrove,et al.  Investigation of the benefits of plasma deposition for the additive layer manufacture of Ti–6Al–4V , 2012 .

[24]  B. Baufeld,et al.  Additive manufacturing of Ti–6Al–4V components by shaped metal deposition: Microstructure and mechanical properties , 2010 .

[25]  F. Klocke,et al.  Consolidation phenomena in laser and powder-bed based layered manufacturing , 2007 .

[26]  R Kovacevic,et al.  Microplasma powder deposition as a new solid freeform fabrication process , 2003 .

[27]  Radovan Kovacevic,et al.  Rapid prototyping of 5356-aluminum alloy based on variable polarity gas tungsten arc welding: process control and microstructure , 2002 .

[28]  K. Taminger,et al.  Characterization of 2219 Aluminum Produced by Electron Beam Freeform Fabrication , 2002 .