Energy monitoring and quality control of a single screw extruder

Polymer extrusion, in which a polymer is melted and conveyed to a mould or die, forms the basis of most polymer processing techniques. Extruders frequently run at non-optimised conditions and can account for 15–20% of overall process energy losses. In times of increasing energy efficiency such losses are a major concern for the industry. Product quality, which depends on the homogeneity and stability of the melt flow which in turn depends on melt temperature and screw speed, is also an issue of concern of processors. Gear pumps can be used to improve the stability of the production line, but the cost is usually high. Likewise it is possible to introduce energy meters but they also add to the capital cost of the machine. Advanced control incorporating soft sensing capabilities offers opportunities to this industry to improve both quality and energy efficiency. Due to strong correlations between the critical variables, such as the melt temperature and melt pressure, traditional decentralized PID (Proportional–Integral–Derivative) control is incapable of handling such processes if stricter product specifications are imposed or the material is changed from one batch to another. In this paper, new real-time energy monitoring methods have been introduced without the need to install power meters or develop data-driven models. The effects of process settings on energy efficiency and melt quality are then studied based on developed monitoring methods. Process variables include barrel heating temperature, water cooling temperature, and screw speed. Finally, a fuzzy logic controller is developed for a single screw extruder to achieve high melt quality. The resultant performance of the developed controller has shown it to be a satisfactory alternative to the expensive gear pump. Energy efficiency of the extruder can further be achieved by optimising the temperature settings. Experimental results from open-loop control and fuzzy control on a Killion 25mm single screw extruder are presented to confirm the efficacy of the proposed approach.

[1]  Marion McAfee,et al.  A Soft Sensor for viscosity control of polymer extrusion , 2007, 2007 European Control Conference (ECC).

[2]  P. A. Taylor,et al.  Adaptive and multivariable control of a single screw extrusion system , 1984 .

[3]  Eugene Lai,et al.  Modeling of the plasticating process in a single‐screw extruder: A fast‐track approach , 2000 .

[4]  Jing Deng,et al.  Modelling the Effects of Operating Conditions on Motor Power Consumption in Single Screw Extrusion , 2010, LSMS/ICSEE.

[5]  Jing Deng,et al.  ‘Soft-sensor’ for real-time monitoring of melt viscosity in polymer extrusion process , 2010, 49th IEEE Conference on Decision and Control (CDC).

[6]  Phil Coates,et al.  Thermal optimisation of polymer extrusion using in-process monitoring techniques , 2013 .

[7]  Sergio M. Savaresi,et al.  Design of a feedback control system for real-time control of flow in a single-screw extruder , 2006 .

[8]  Kang Li,et al.  Dynamic grey-box modeling for online monitoring of extrusion viscosity , 2012 .

[9]  Shih-hsuan Chiu,et al.  In-line viscosity control in an extrusion process with a fuzzy gain scheduled PID controller , 1999 .

[10]  Sirish L. Shah,et al.  Identification of transient responses of a plasticating twin screw extruder due to excitation in feed rate , 2011 .

[11]  G. Hassan,et al.  Model reference optimal steady‐state adaptive computer control of plastics extrusion processes , 1981 .

[12]  Kang Li,et al.  Dynamic gray-box modeling for on-line monitoring of polymer extrusion viscosity , 2012 .

[13]  M. H. Iqbal,et al.  Advanced control of the twin screw extruder , 2010 .

[14]  George W. Irwin,et al.  A New Gradient Descent Approach for Local Learning of Fuzzy Neural Models , 2013, IEEE Transactions on Fuzzy Systems.

[15]  Yueh-Jaw Lin,et al.  System Identification for State Feedback Integral Observer Control of Polymer Plastic Extrusion , 1997 .

[16]  Stephen T. Balke,et al.  Development of an in-line rheometer suitable for reactive extrusion processes , 1991 .

[17]  Shih-Hsuan Chiu,et al.  In‐line viscosity fuzzy control , 2001 .

[18]  G. Irwin,et al.  Extruder Melt Temperature Control With Fuzzy Logic , 2011 .

[19]  R. Kent,et al.  Energy management in plastics processing — framework for measurement, assessment and prediction , 2008 .

[20]  Subbu S. Venkatraman,et al.  A comparison of torsional and capillary rheometry for polymer melts: The Cox‐Merz rule revisited , 1990 .

[21]  P. A. Taylor,et al.  On the dynamics and control of a plasticating extruder , 1982 .

[22]  Phil Coates,et al.  Investigation of the process energy demand in polymer extrusion: A brief review and an experimental study , 2014 .

[23]  E. C. Brown,et al.  The effect of screw geometry on melt temperature profile in single screw extrusion , 2006 .

[24]  Sirish L. Shah,et al.  New Approach To Develop Dynamic Gray Box Model for a Plasticating Twin-Screw Extruder† , 2010 .

[25]  O. Amano,et al.  Temperature measurements of polymer melts in the heating barrel during injection molding. Part 3: Effects of screw geometry , 1990 .