Evaporative heat transfer model of a loop heat pipe with bidisperse wick structure

Abstract A mathematical model of evaporative heat transfer in a loop heat pipe was developed and compared with experiments. The steady-state thermal performance was predicted for different sintered nickel wicks, including monoporous and bidisperse structures. The effect of wick pore size distribution on heat transfer was taken into consideration. The wick in the evaporator was assumed to possess three regions during vaporization from an applied heat load: a vapor blanket, a two-phase region, and a saturated liquid region. The evaporator wall temperature and the total thermal resistance at different heat loads were predicted using ammonia as the working fluid. The predictions showed distinct heat transfer characteristics and higher performance for the bidisperse wick in contrast with monoporous wick. A bidisperse wick was able to decrease the thickness of the vapor blanket region, which presents a thermal resistance and causes lower heat transfer capacity of the evaporator. Additionally, a validation test presented good agreement with the experiments.

[1]  Jentung Ku,et al.  Operating Characteristics of Loop Heat Pipes , 1999 .

[2]  Amir Faghri,et al.  Heat transfer in the inverted meniscus type evaporator at high heat fluxes , 1995 .

[3]  R. Lockhart.  Proposed Correlation of Data for Isothermal Two-Phase, Two-Component Flow in Pipes , 1949 .

[4]  S. K. Konev,et al.  Investigation of boiling in capillary structures , 1987 .

[5]  Amir Faghri,et al.  Estimation of the maximum heat flux in the inverted meniscus type evaporator of a flat miniature heat pipe , 1996 .

[6]  Tadej Semenic,et al.  Experimental study of biporous wicks for high heat flux applications , 2009 .

[7]  Quan Liao,et al.  On capillary-driven flow and phase-change heat transfer in a porous structure heated by a finned surface: measurements and modeling , 2000 .

[8]  Yu.F. Maydanik,et al.  Loop heat pipes , 2005 .

[9]  Triem T. Hoang,et al.  Mathematical modeling of loop heat pipes and experimental validation , 1999 .

[10]  Mark T. North,et al.  High heat flux loop heat pipes , 1997 .

[11]  Jocelyn Bonjour,et al.  Parametric analysis of loop heat pipe operation: a literature review , 2007 .

[12]  Aliakbar Akbarzadeh,et al.  Effect of Wick Characteristics on the Thermal Performance of the Miniature Loop Heat Pipe , 2009 .

[13]  David A. Wolf,et al.  Loop Heat Pipes - Their Performance and Potential , 1994 .

[14]  Chun-Nan Chen,et al.  Heat transfer analysis of a loop heat pipe with biporous wicks , 2009 .

[15]  Jentung Ku,et al.  Heat and Mass Transfer in Loop Heat Pipes , 2003 .

[16]  M. A. Chernysheva,et al.  Heat and Mass Transfer in Evaporator of Loop Heat Pipe , 2009 .

[17]  Guiping Lin,et al.  Mathematical modeling of steady-state operation of a loop heat pipe , 2009 .

[18]  John Goldak,et al.  Numerical analysis of heat and mass transfer in the capillary structure of a loop heat pipe , 2006 .

[19]  J. Bonjour,et al.  Analytical Model for Characterization of Loop Heat Pipes , 2008 .

[20]  M. A. Chernysheva,et al.  Operating temperature and distribution of a working fluid in LHP , 2007 .

[21]  A. S. Demidov,et al.  Investigation of heat and mass transfer in the evaporation zone of a heat pipe operating by the ‘inverted meniscus’ principle , 1994 .

[22]  Ivan Catton,et al.  Thermophysical Properties of Biporous Heat Pipe Evaporators , 2008 .