Performance Prediction for Ultrasonic Spot Welds of Short Carbon Fiber-Reinforced Composites Under Shear Loading

[1]  B. Chua,et al.  Effect of Deformation and Temperature Paths in Severe Plastic Deformation Using Groove Pressing on Microstructure, Texture, and Mechanical Properties of AZ31-O , 2015 .

[2]  R. Hinterhölzl,et al.  Fracture mechanical investigations and cohesive zone failure modelling on automotive composites , 2014 .

[3]  Wayne W. Cai,et al.  Dynamic Response of Battery Tabs Under Ultrasonic Welding , 2013 .

[4]  Jorge Arinez,et al.  Characterization of weld attributes in ultrasonic welding of short carbon fiber reinforced thermoplastic composites , 2017 .

[5]  Mihaela Banu,et al.  Performance prediction for ultrasonically welded dissimilar materials joints , 2017 .

[6]  A. Poitou,et al.  Ultrasonic Welding. Simulation of the Flow at the Interface , 2010 .

[7]  M. D. Thouless,et al.  Deformation and fracture of adhesive layers constrained by plastically-deforming adherends , 2000 .

[8]  M. D. Thouless,et al.  Use of a cohesive-zone model to analyze the fracture of a fiber-reinforced polymer-matrix composite , 2005 .

[9]  Gilles A. Francfort,et al.  Homogenization and mechanical dissipation in thermoviscoelasticity , 1986 .

[10]  M. D. Thouless,et al.  Mixed-mode fracture analyses of plastically-deforming adhesive joints , 2001 .

[11]  K. Prakasan,et al.  Temperature and stress distribution in ultrasonic metal welding—An FEA-based study , 2009 .

[12]  S. Tsai,et al.  Introduction to composite materials , 1980 .

[13]  M. D. Thouless,et al.  Cohesive-zone modelling of the deformation and fracture of spot-welded joints , 2005 .

[14]  Charles L. Tucker,et al.  Stereological measurement and error estimates for three-dimensional fiber orientation , 1992 .

[15]  W. Ng.  Study of Vibration and viscoelastic heating of thermoplastic parts subjected to ultrasonic excitation , 1996 .

[16]  Z. Maekawa,et al.  Flexural Stiffness of Injection Molded Glass Fiber Reinforced Thermoplastics , 1995 .

[17]  Steven Le Corre,et al.  Ultrasonic Welding of Thermoplastic Composites, Modeling of the Process. , 2008 .

[18]  M. D. Thouless,et al.  Elastic–plastic mode-II fracture of adhesive joints , 2001 .

[19]  Xiaodong Wang,et al.  Study on Heating Process of Ultrasonic Welding for Thermoplastics , 2010 .

[20]  Chandra Nath,et al.  Estimating the Cohesive Zone Model Parameters of Carbon Nanotube–Polymer Interface for Machining Simulations , 2014 .

[21]  T. Keller,et al.  Mixed-mode fatigue and fracture behavior of adhesively-bonded composite joints , 2015 .

[22]  Jingjing Li,et al.  Special Issue: Forming and Joining of Lightweight and Multimaterial Systems , 2015 .

[23]  Glaucio H. Paulino,et al.  Mode I fracture of adhesive joints using tailored cohesive zone models , 2008 .

[24]  Jwo Pan,et al.  Residual Stresses Due to Rigid Cylinder Indentation and Rolling at a Very High Rolling Load , 2015 .

[25]  I. F. Villegas,et al.  Modeling of the heating phenomena in ultrasonic welding of thermoplastic composites with flat energy directors , 2014 .

[26]  Laine Mears,et al.  The Correlation of the Volumetric Wear Rate of Turning Tool Inserts With Carbide Grain Sizes , 2015 .

[27]  Wayne W. Cai,et al.  Analysis of Weld Formation in Multilayer Ultrasonic Metal Welding Using High-Speed Images , 2015 .

[28]  S. Nassar,et al.  Effect of Adhesive Nanoparticle Enrichment on Static Load Transfer Capacity and Failure Mode of Bonded Steel–Magnesium Single Lap Joints , 2015 .

[29]  Ultrasonic Welding of Thermoplastic Composites, Modeling of the Process. , 2008 .