Fabrication of a Graded-Index Circular-Core Polymer Parallel Optical Waveguide Using a Microdispenser for a High-Density Optical Printed Circuit Board

A simple fabrication method for multimode polymer optical waveguides with graded-index (GI) circular cores is introduced for use in optical printed circuit boards (O-PCBs). The new method, named “Mosquito method,” utilizes a microdispenser to dispense a viscous monomer directly onto the substrates. By optimizing the dispensing conditions, 12-channel parallel waveguides with circular GI-cores (core diameter of 40 μm) are successfully fabricated using the Mosquito method. The advantages of GI-core waveguides for O-PCB applications are discussed by comparing the optical characteristics of the fabricated waveguides with those of conventional step-index (SI) square-core polymer waveguides, and even with those of silica-based GI multimode fibers (MMFs), as an ideal case. To the best of our knowledge, this is the first comparison of SI- and GI-core multimode polymer waveguides that are composed of the same polymer materials and that have similar core and pitch sizes. We experimentally demonstrate that the GI circular-core polymer waveguides fabricated by the Mosquito method have sufficiently low propagation loss (0.033 dB/cm at 850 nm), low connection loss with GI-MMFs, and low interchannel crosstalk. We observe approximately -50 dB of interchannel crosstalk in the 250-μm pitch GI-core waveguide fabricated, which is almost 10 dB lower than in the SI counterpart. Furthermore, sufficiently low crosstalk is maintained in a half-pitch GI-core waveguide fabricated by the Mosquito method.

[1]  Takaaki Ishigure,et al.  Polymer parallel optical waveguide with graded-index rectangular cores and its dispersion analysis. , 2009, Optics express.

[2]  J. Beals,et al.  Cost-Effective Multimode Polymer Waveguides for High-Speed On-Board Optical Interconnects , 2009, IEEE Journal of Quantum Electronics.

[3]  C. Schow,et al.  Terabit/s-Class Optical PCB Links Incorporating 360-Gb/s Bidirectional 850 nm Parallel Optical Transceivers , 2012, Journal of Lightwave Technology.

[4]  Mike Ignatowski,et al.  Exploitation of optical interconnects in future server architectures , 2005, IBM J. Res. Dev..

[5]  Takaaki Ishigure,et al.  Polymer optical waveguide with multiple graded-index cores for on-board interconnects fabricated using soft-lithography. , 2010, Optics express.

[6]  T. Ishigure,et al.  High-Density 2$\,\times\,$4 Channel Polymer Optical Waveguide With Graded-Index Circular Cores , 2009, Journal of Lightwave Technology.

[7]  Tetsuya Mori,et al.  Optical and electrical hybrid flexible printed circuit boards with unique photo-defined polymer waveguide layers , 2010, OPTO.

[8]  Hisashi Sawada,et al.  New Plastic Optical Fiber With Polycarbonate Core And Fluorescence-Doped Fiber For High Temperature Use , 1987, Other Conferences.

[9]  Kenji Hara,et al.  Preparation and properties of novel silicone-based flexible optical waveguide , 2006, SPIE Optics East.

[10]  Steven E. Golowich,et al.  Development of system specification for laser-optimized 50-/spl mu/m multimode fiber for multigigabit short-wavelength LANs , 2003 .

[11]  Takaaki Ishigure,et al.  Link power budget advantage in GI-core polymer optical waveguide link for optical printed circuit boards , 2012, Other Conferences.

[12]  Christian Baks,et al.  Terabit/sec-class board-level optical interconnects through polymer waveguides using 24-channel bidirectional transceiver modules , 2011, 2011 IEEE 61st Electronic Components and Technology Conference (ECTC).

[13]  Y. Koike,et al.  Mode-coupling control and new index profile of GI POF for restricted-launch condition in very-short-reach networks , 2005, Journal of Lightwave Technology.

[14]  T. Ishigure,et al.  Fabrication and inter-channel crosstalk analysis of polymer optical waveguides with W-shaped index profile for high-density optical interconnections. , 2011, Optics express.

[15]  J. Goldhar,et al.  Dispensed polymer waveguides and laser-fabricated couplers for optical interconnects on printed circuit boards. , 2007, Applied optics.

[16]  Charles Archer,et al.  Breaking the petaflops barrier , 2009, IBM J. Res. Dev..

[17]  Hsiang-Han Hsu,et al.  Maximum channel density in multimode optical waveguides for parallel interconnections , 2011, 2011 IEEE 61st Electronic Components and Technology Conference (ECTC).

[18]  H. Schroder,et al.  Polymer Optical Interconnects—A Scalable Large-Area Panel Processing Approach , 2006, IEEE Transactions on Advanced Packaging.

[19]  T. Ishigure,et al.  High-density channel alignment of graded index core polymer optical waveguide and its crosstalk analysis with ray tracing method. , 2010, Optics express.

[20]  Akira Tanaka,et al.  New plastic optical fiber using polycarbonate core , 1987 .

[21]  K. Adachi,et al.  20-Gb/s/ch High-Speed Low-Power 1-Tb/s Multilayer Optical Printed Circuit Board With Lens-Integrated Optical Devices and CMOS IC , 2011, IEEE Photonics Technology Letters.

[22]  J. Chappell,et al.  Variation in the line stability of an inkjet printed optical waveguide-applicable material , 2008, 2008 2nd Electronics System-Integration Technology Conference.