Determinants and magnitudes of manual force strengths and joint moments during two-handed standing maximal horizontal pushing and pulling

Abstract Pushing and pulling are common occupational exertions that are increasingly associated with musculoskeletal complaints. This study focuses on the sensitivity of shoulder capacity to gender, handle height, exertion type (push or pull) and handle orientation for these tasks. All factors except for handle orientation influenced unilateral and total manual force strength (p < 0.01), with exertion type being the most influential. Interaction effects also existed between handle height and exertion type. Additionally, joint moments at the shoulders and low back were influenced by all factors studied (p < 0.01), with exertion type again being most influential. Knowledge of the relative influence of multiple factors on shoulder capacity can provide guidance regarding these factors when designing or evaluating occupational pushing and pulling tasks for a diverse population. Practitioner Summary: pushing and pulling comprise nearly half of all manual materials handling tasks. Practitioners often assess, design or modify these tasks while incorporating constraints, including manual force direction and handle interface. This study provides guidance to aid design of pushing and pulling tasks in the context of shoulder physical capacity.

[1]  Arun Garg,et al.  One-handed dynamic pulling strength with special reference to speed, handle height and angles of pulling , 1990 .

[2]  D B Chaffin,et al.  An ergonomic evaluation of handle height and load in maximal and submaximal cart pushing. , 1995, Applied ergonomics.

[3]  Han C. G. Kemper,et al.  Loading and unloading by lorry drivers and musculoskeletal complaints , 1993 .

[4]  Ciriello Vm,et al.  The effects of task duration on psychophysically-determined maximum acceptable weights and forces , 1990 .

[5]  G M Hägg,et al.  Normalization of surface EMG amplitude from the upper trapezius muscle in ergonomic studies - A review. , 1995, Journal of electromyography and kinesiology : official journal of the International Society of Electrophysiological Kinesiology.

[6]  Terrence John Stobbe.  The development of a practical strength testing program for industry , 1982 .

[7]  Clark R Dickerson,et al.  Relationships between psychophysically acceptable and maximum voluntary hand force capacity in the context of underlying biomechanical limitations. , 2012, Applied ergonomics.

[8]  Ravishankar K. Iyer,et al.  Experimental evaluation , 1995 .

[9]  ADJ Pinder,et al.  Omnidirectional assessment of one-handed manual strength at three handle heights. , 1995, Clinical biomechanics.

[10]  S. Snook.  The design of manual handling tasks. , 1978, Ergonomics.

[11]  Scott MacKinnon,et al.  Effect of the reach distance on the execution of one-handed submaximal pull forces , 2005 .

[12]  L. A. Rozendaal,et al.  Reliability of force direction dependent EMG parameters of shoulder muscles for clinical measurements. , 2004, Clinical biomechanics.

[13]  Thomas J Armstrong,et al.  Effects of handle orientation, gloves, handle friction and elbow posture on maximum horizontal pull and push forces , 2010, Ergonomics.

[14]  Don B. Chaffin,et al.  Kinematics, Kinetics, and Psychophysical Perceptions in Symmetric and Twisting Pushing and Pulling Tasks , 1996, Hum. Factors.

[15]  S H Snook,et al.  The design of manual handling tasks: revised tables of maximum acceptable weights and forces. , 1991, Ergonomics.

[16]  D. Grieve,et al.  Human strength capabilities during one-handed maximum voluntary exertions in the fore and aft plane. , 1991, Ergonomics.

[17]  A J van der Beek,et al.  Gender differences in exerted forces and physiological load during pushing and pulling of wheeled cages by postal workers , 2000, Ergonomics.

[18]  D J Habes,et al.  An electromyographic study of strength and upper extremity muscle activity in simulated meat cutting tasks. , 1997, Applied ergonomics.

[19]  Don B Chaffin,et al.  The relationship between shoulder torques and the perception of muscular effort in loaded reaches , 2006, Ergonomics.

[20]  E W Abel,et al.  The design of attendant propelled wheelchairs , 1991, Prosthetics and orthotics international.

[21]  P Buckle,et al.  Risk factors for incident neck and shoulder pain in hospital nurses , 2003, Occupational and environmental medicine.

[22]  Alfred A. Amendola,et al.  The effect of handle height and cart load on the initial hand forces in cart pushing and pulling , 1999 .

[23]  B J Daams.  Static force exertion in postures with different degrees of freedom. , 1993, Ergonomics.

[24]  Wayne Maynard,et al.  One-handed standing pull strength in different postures: normative data. , 2013, Applied ergonomics.

[25]  K. Cureton,et al.  Sex difference in muscular strength in equally-trained men and women. , 1987, Ergonomics.

[26]  William S. Marras,et al.  Modification of an EMG-assisted biomechanical model for pushing and pulling , 2007 .

[27]  S T Pheasant,et al.  Vector representations of human strength in whole body exertion. , 1982, Applied ergonomics.

[28]  S N MacKinnon,et al.  Isometric pull forces in the sagittal plane. , 1998, Applied ergonomics.

[29]  Shrawan Kumar.  Upper body push-pull strength of normal young adults in sagittal plane at three heights , 1995 .

[30]  A Schultz,et al.  Maximum voluntary strengths of male adults in some lifting, pushing and pulling activities. , 1980, Ergonomics.

[31]  A. Ertaud,et al.  LOADING AND UNLOADING , 1958 .

[32]  Roger Haslam,et al.  Maximum acceptable loads for pushing and pulling on floor surfaces with good and reduced resistance to slipping , 2002 .

[33]  Don B Chaffin,et al.  Experimental evaluation of a computational shoulder musculoskeletal model. , 2008, Clinical biomechanics.

[34]  A J van der Beek,et al.  Pushing and pulling in association with low back and shoulder complaints , 2002, Occupational and environmental medicine.

[35]  Biman Das,et al.  Ergonomics evaluation and redesign of a hospital meal cart. , 2002, Applied ergonomics.

[36]  M. M. Ayoub,et al.  Effects of Operator Stance on Pushing and Pulling Tasks , 1974 .

[37]  I Kingma,et al.  Force direction and physical load in dynamic pushing and pulling , 2000, Ergonomics.

[38]  Clark R Dickerson,et al.  The influence of providing feedback on force production and within-participant reproducibility during maximal voluntary exertions for the anterior deltoid, middle deltoid, and infraspinatus. , 2010, Journal of electromyography and kinesiology : official journal of the International Society of Electrophysiological Kinesiology.

[39]  M. Frings-Dresen,et al.  Pushing and pulling in relation to musculoskeletal disorders: a review of risk factors. , 1998, Ergonomics.

[40]  William S Marras,et al.  Loading along the lumbar spine as influence by speed, control, load magnitude, and handle height during pushing. , 2009, Clinical biomechanics.

[41]  Laubach Ll.  Body composition in relation to muscle strength and range of joint motion. , 1969 .

[42]  J. Mcconville,et al.  The relationship of strength to body size and typology , 1969 .

[43]  S H Snook,et al.  The effects of task duration on psychophysically-determined maximum acceptable weights and forces. , 1990, Ergonomics.

[44]  D B Chaffin,et al.  Ergonomics guide for the assessment of human static strength. , 1975, American Industrial Hygiene Association journal.

[45]  Don B Chaffin,et al.  A mathematical musculoskeletal shoulder model for proactive ergonomic analysis , 2007, Computer methods in biomechanics and biomedical engineering.

[46]  Andris Freivalds,et al.  Pushing and pulling carts and two-wheeled hand trucks , 2005 .

[47]  Shrawan Kumar,et al.  Symmetric and Asymmetric Two-Handed Pull-Push Strength of Young Adults , 1995, Hum. Factors.

[48]  Stover H. Snook,et al.  The Ergonomics Society The Society's Lecture 1978. THE DESIGN OF MANUAL HANDLING TASKS , 1978 .

[49]  Christine M Haslegrave,et al.  Ready steady push – a study of the role of arm posture in manual exertions , 2008, Ergonomics.

[50]  Biman Das,et al.  Isometric Pull-Push Strengths in Workspace: 1. Strength Profiles , 2004, International journal of occupational safety and ergonomics : JOSE.

[51]  R E Hughes,et al.  Age-Related Changes in Normal Isometric Shoulder Strength , 1999, The American journal of sports medicine.

[52]  Kathleen M. Robinette,et al.  Civilian American and European Surface Anthropometry Resource (CAESAR), Final Report. Volume 1. Summary , 2002 .

[53]  S H Snook,et al.  Further Studies of Psychophysically Determined Maximum Acceptable Weights and Forces , 1993, Human factors.

[54]  Don B. Chaffin,et al.  Volitional Postures during Maximal Push/Pull Exertions in the Sagittal Plane , 1981, Human factors.

[55]  A. Pandya,et al.  Correlation and prediction of dynamic human isolated joint strength from lean body mass , 1992 .

[56]  Idsart Kingma,et al.  Ltd Registered in England and Wales Registered Number : 1072954 Registered office : , 2011 .

[57]  Chien-Chi Chang,et al.  Effects of handle orientation and between-handle distance on bi-manual isometric push strength. , 2012, Applied ergonomics.

[58]  Don B. Chaffin,et al.  A STUDY OF SLIP POTENTIAL DURING CART PUSHING AND PULLING , 1992 .

[59]  W. M. Keyserling,et al.  Preemployment strength testing , 1978 .

[60]  Mark S. Young,et al.  Kodak's Ergonomic Design for People at Work , 2009 .

[61]  Clark R Dickerson,et al.  Estimating maximum and psychophysically acceptable hand forces using a biomechanical weakest link approach , 2014, Computer methods in biomechanics and biomedical engineering.