Cost-effectiveness analysis for computer-aided surgical simulation in complex cranio-maxillofacial surgery.

PURPOSE The purpose of this study is to assess the costs and benefits of computer-aided surgical simulation (CASS) and to compare it with the current surgical planning methods for complex cranio-maxillofacial (CMF) surgery. MATERIALS AND METHODS The comparison of methods applies to all CMF surgeries where the patient's condition is severe enough to undergo a computed tomography scan and a stereolithographic model is necessary for the surgical planning process. The costs for each method can be divided into time and other costs. The time was estimated based on the authors' experience as well as on a survey of a small group of 6 experienced CMF surgeons in the United States. The other costs were estimated based on the authors' experience. RESULTS CASS has lower costs in terms of surgeon time, patient time, and material costs. Specifically, total surgeon hours spent in planning are 5.25 hours compared with 9.75 for current standard methods. Material and scanning costs are Dollars 1,900 for CASS compared with about Dollars 3,510 for standard methods. Patient time for planning is reduced from 4.75 hours to 2.25 hours with CASS. The reduction in both time and other costs remains when the fixed fee costs of CASS are added to the variable costs. Amortized across the 600 patients per year (1,800 for the assumed 3-year life of the training and software), this adds only a few dollars and a fraction of an hour per surgery. Even in the case of a small clinic when the cost is amortized for 6 patients per year (18 patients for the assumed 3-year life of the training and software), the per surgery costs (9.65 hours and Dollars 2,456) will still favor CASS. CONCLUSION Any great new design should consist of at least 2 of the 3 following features: faster, cheaper, and better outcome. This analysis demonstrates that CASS is faster and less costly than the current standard planning methods for complex CMF surgery. Previous studies have also shown that CASS results in better surgical outcomes. Thus, in all regards, CASS appears to be at least as good as the current methods of surgical planning.

[1]  Dongfeng Wang,et al.  Three-dimensional virtual-reality surgical planning and soft-tissue prediction for orthognathic surgery , 2001, IEEE Transactions on Information Technology in Biomedicine.

[2]  Jaime Gateno,et al.  Three-Dimensional Surgical Planning for Maxillary and Midface Distraction Osteogenesis , 2003, The Journal of craniofacial surgery.

[3]  J. Mühling,et al.  Computer assisted oral and maxillofacial surgery--a review and an assessment of technology. , 2001, International journal of oral and maxillofacial surgery.

[4]  R. Kikinis,et al.  Computer‐Assisted Three‐Dimensional Planning in Craniofacial Surgery , 1993, Plastic and reconstructive surgery.

[5]  N Samman,et al.  Computer-assisted three-dimensional surgical planning and simulation: 3D virtual osteotomy. , 2000, International journal of oral and maxillofacial surgery.

[6]  W. Proffit,et al.  Who seeks surgical-orthodontic treatment? , 1990, The International journal of adult orthodontics and orthognathic surgery.

[7]  T Sohmura,et al.  Prototype of simulation of orthognathic surgery using a virtual reality haptic device. , 2004, International journal of oral and maxillofacial surgery.

[8]  Proffit Wr,et al.  The prevalence of facial asymmetry in the dentofacial deformities population at the University of North Carolina. , 1997 .

[9]  M. Feinleib National Center for Health Statistics (NCHS) , 2005 .

[10]  Jaime Gateno,et al.  Three-dimensional computer-aided surgical simulation for maxillofacial surgery. , 2005, Atlas of the oral and maxillofacial surgery clinics of North America.

[11]  James A Lipton Introduction: National institutes of health technology assessment conference on management of temporomandibular disorders , 1997 .

[12]  K. Maurer,et al.  Third national health and nutrition examination survey , 1985 .

[13]  S. Pruzansky,et al.  Craniosynostosis : diagnosis, evaluation, and management , 1986 .

[14]  L. Kaban Biomedical technology revolution: opportunities and challenges for oral and maxillofacial surgeons. , 2002, International journal of oral and maxillofacial surgery.

[15]  N Samman,et al.  Three-dimensional virtual reality surgical planning and simulation workbench for orthognathic surgery. , 2000, The International journal of adult orthodontics and orthognathic surgery.

[16]  Robert J. Gorlin,et al.  Syndromes of the Head and Neck , 1976 .

[17]  R Kikinis,et al.  Development of a three-dimensional treatment planning system based on computed tomographic data. , 2002, International journal of oral and maxillofacial surgery.