Experimental detection of forming limit strains on samples with multiple local necks

Abstract Sheet metal formability is traditionally described by the forming limit curve (FLC). Experimental FLCs are obtained by performing formability tests and determining failure strains. The strains are usually measured either by etching a grid on the sheet surface or by digital image correlation (DIC). Ductile metal sheets fail primarily by local necking which introduces a severe strain gradient in the failure region. This makes accurate detection of the failure strains challenging. An international standard (ISO12004-2:2008) was introduced in 2008 to unify the procedure of FLC detection; prior to this large discrepancies were observed between the results reported by different laboratories. The main limitation of the standard method for detection of forming limits is that its application is limited to cases where a single local neck is formed in the metal sheet prior to fracture. In the case of multiple local necks, the samples are simply discarded. Furthermore, the standard method does not include any guidelines to distinguish the failure by local necking and direct failure by fracture. One of the advantages of DIC over the traditional etched-grid technique is that the former allows us to obtain not only the strain distribution but also its history. This allows for alternative methods for detection of forming limit strains. This paper introduces a DIC-based method which was specially developed to handle the case of multiple local necks and to distinguish failure by local necking from direct fracture automatically. The method is not confined to a single test type and can be used in combination with different formability tests as long as DIC is used to measure strains.

[1]  Manfred Geiger,et al.  Time dependent determination of forming limit diagrams , 2010 .

[2]  Gorton M. Goodwin,et al.  Application of Strain Analysis to Sheet Metal Forming Problems in the Press Shop , 1968 .

[3]  Marion Merklein,et al.  Time Dependent FLC Determination Comparison of Different Algorithms to Detect the Onset of Unstable Necking before Fracture , 2013 .

[4]  Magnus Langseth,et al.  Modeling of textured aluminum alloys used in a bumper system: Material tests and characterization , 2006 .

[5]  H. Brinkman,et al.  Crystal-plasticity simulation of the correlation of microtexture and roping in AA 6xxx Al–Mg–Si sheet alloys for automotive applications , 2012 .

[6]  Stuart P. Keeler,et al.  Circular Grid System — A Valuable Aid for Evaluating Sheet Metal Formability , 1968 .

[7]  Determination of Forming Limit Strains Using Marciniak-Kuczynski Tests and Automated Digital Image Correlation Procedures , 2012 .

[8]  O. Hopperstad,et al.  Experimental Detection of the Onset of Local Necking in an Aluminium Sheet , 2014 .

[9]  Michel Vermeulen,et al.  Statistical evaluation of the uncertainty of experimentally characterised forming limits of sheet steel. , 2001 .

[10]  O. Hopperstad,et al.  Estimation of forming limit diagrams by the use of the finite element method and Monte Carlo simulation , 2009 .

[11]  Pavel Hora,et al.  New algorithm for a robust user-independent evaluation of beginning instability for the experimental FLC determination , 2011 .

[12]  Evaluation of Experimental Forming Limit Curves and Investigation of Strain Rate Sensitivity for the Start of Local Necking , 2011 .

[13]  Baiyan He,et al.  Measuring forming limit strains with digital image correlation analysis , 2014 .

[14]  Quan Situ,et al.  Determination of forming limit diagrams of sheet materials with a hybrid experimental–numerical approach , 2011 .

[15]  M. Gorji,et al.  A generalized approach for the prediction of necking and rupture phenomena in the sheet metal forming , 2012 .

[16]  P Vacher,et al.  Bidimensional strain measurement using digital images , 1999 .

[17]  R. Arrieux,et al.  Determination of the Forming Limit Diagrams Using Image Analysis by the Corelation Method , 1999 .

[18]  Z. Marciniak,et al.  Limit strains in the processes of stretch-forming sheet metal , 1967 .