Mechanical deflection of a free-standing pellicle for extreme ultraviolet lithography

Display Omitted Free-standing EUV pellicle is desirable to avoid non-uniform intensity.Nonlinear deflection model is used to predict deflection of EUV pellicle.Deflection of pellicle satisfies the desired specification at full scale.Trade-off between mechanical and optical properties is highlighted. In extreme ultraviolet lithography (EUVL), a pellicle is a thin (a few nanometers in scale) protective membrane that can prevent the mask from suffering from defects. However, this thin film can be easily deformed by gravity and other forces. Although the hexagonal-shaped mesh support structure can decrease the stress caused by external pressure, its structural shape can degrade the image quality on the wafer. Therefore, studying the deflection of a free-standing EUV pellicle is needed. We revisited the plate theory and found that a nonlinear deflection term should be added to the deflection equation. The deflection of a 50nm thick polysilicon pellicle is about 100µm for a full-scale (100mmi?100mm) pellicle. Previously, researchers have tried to include graphene in multi-layer EUV pellicles in order to enhance the mechanical properties of the film. We found that the addition of graphene did not cause any serious deflection problems. This study shows that a free-standing EUV pellicle without mesh support can be used without any noticeable deflection effect on the pattern fidelity.

[1]  J. A. Taylor.  The mechanical properties and microstructure of plasma enhanced chemical vapor deposited silicon nitride thin films , 1991 .

[2]  T. Kenny,et al.  What is the Young's Modulus of Silicon? , 2010, Journal of Microelectromechanical Systems.

[3]  J. Maibach,et al.  A new analytical solution for the load-deflection of square membranes , 1995 .

[4]  Luigi Scaccabarozzi,et al.  Investigation of EUV pellicle feasibility , 2013, Advanced Lithography.

[5]  P. Lin.  The in-situ measurement of mechanical properties of multi-layer coatings , 1990 .

[6]  Joost J. Vlassak,et al.  A new bulge test technique for the determination of Young’s modulus and Poisson’s ratio of thin films , 1992 .

[7]  Jun-Taek Park,et al.  Effect of extreme-ultraviolet pellicle support to patterned mask , 2012, Advanced Lithography.

[8]  P. Ming,et al.  Ab initio calculation of ideal strength and phonon instability of graphene under tension , 2007 .

[9]  Isaac Todhunter.  A History of the Theory of Elasticity and of the Strength of Materials by Isaac Todhunter , 2010 .

[10]  V. Bakshi.  EUV Lithography , 2008 .

[11]  Junhua Kong,et al.  A high throughput method for preparation of highly conductive functionalized graphene and conductive polymer nanocomposites , 2012 .

[12]  E. Lavernia,et al.  Processing of molybdenum disilicide , 1994, Journal of Materials Science.

[13]  A. Boccaccini,et al.  Microwave processing of glass matrix composites containing controlled isolated porosity , 2001 .

[14]  Hye-keun Oh,et al.  Temperature behavior of pellicles in extreme ultraviolet lithography , 2012 .

[15]  Koji Koyamada,et al.  Systems Modeling and Simulation , 2007 .

[16]  S. Timoshenko,et al.  THEORY OF PLATES AND SHELLS , 1959 .

[17]  R. Piner,et al.  Mechanical properties of monolayer graphene oxide. , 2010, ACS nano.

[18]  K. Lang,et al.  Measurement of Young’s modulus and residual stress of thin SiC layers for MEMS high temperature applications , 2012 .

[19]  Eytan Barouch,et al.  A study of the effect of pellicle support structures on aerial-image quality in EUV lithography by rigorous electromagnetic simulation , 2014, Advanced Lithography.

[20]  S. C. Pradhan,et al.  A series solution approach to an analytical load-deflection relation for the measurement of mechanical properties of thin films , 1999 .