Optimisation of multiperformance characteristics in electric discharge machining of Aluminium Matrix Composites (AMCs) using Taguchi DOE methodology

This paper presents an investigation on the optimisation of process parameters for the Electric Discharge Machining (EDM) of 6061Al/Al2O3p/20p work specimens by employing the Taguchi Design of Experiment (DOE) methodology. One noise factor, aspect ratio (with two levels), and five control factors, viz. pulse current, pulse ON time, duty cycle, gap voltage and tool electrode lift time (three levels each), with an L18 (21 ? 35) fractional factorial design were selected for the present experiment to obtain the optimal settings of factors and study their effects on multiple performance characteristics, namely, Material Removal Rate (MRR), Tool Wear Rate (TWR) and Surface Roughness (SR). The experimental results were analysed by using Signal-to-Noise (S/N) ratios and Analysis of Variance (ANOVA). This analysis recognised the factors on the basis of their significant effect on the performance measures. The derived optimal levels were then used to conduct validation tests to confirm the effectiveness of this approach.

[1]  Satish V. Kailas,et al.  Influence of processing and reinforcement on microstructure and impact behaviour of magnesium alloy AM100 , 2004 .

[2]  M. K. Surappa,et al.  Aluminium matrix composites: Challenges and opportunities , 2003 .

[3]  H. Hocheng,et al.  Preliminary study of material removal in electrical-discharge machining of SiC/Al , 1997 .

[4]  P.Narender Singh,et al.  Electric discharge machining of Al–10%SiCP as-cast metal matrix composites , 2004 .

[5]  Esther Seiden,et al.  On Orthogonal Arrays , 1966 .

[6]  D. Lloyd.  Particle reinforced aluminium and magnesium matrix composites , 1994 .

[7]  Bruce Boardman,et al.  Metal matrix composites : an opportunity for the off-highway industry , 1990 .

[8]  A. Rajadurai,et al.  Effect of SiC and rotation of electrode on electric discharge machining of Al–SiC composite , 2002 .

[9]  Ranjit K. Roy,et al.  Design of Experiments Using The Taguchi Approach: 16 Steps to Product and Process Improvement , 2001 .

[10]  R. Roy.  A Primer on the Taguchi Method , 1990 .

[11]  Y.-F. Tzeng,et al.  Two-Phase Parameter Design for the Optimisation of the Electrical-Discharge Machining Process Using a Taguchi Dynamic Experiment , 2003 .

[12]  Anthony Kelly,et al.  Composites in context , 1985 .

[13]  P. M. George,et al.  Modelling of machinability parameters of carbon–carbon composite—a response surface approach , 2004 .

[14]  Yan Cherng Lin,et al.  Feasibility study of rotary electrical discharge machining with ball burnishing for Al2O3/6061Al composite , 2000 .

[15]  Yan Cherng Lin,et al.  Surface Improvement Using a Combination of Electrical Discharge Machining with Ball Burnish Machining Based on the Taguchi Method , 2001 .

[16]  Y. Dai,et al.  An Examination of Wire Electrical Discharge Machining (WEDM) of Al2O3 Particulate Reinforced Aluminum Based Composites , 1996 .

[17]  Henry W. Altland,et al.  Engineering Methods for Robust Product Design , 1996 .

[18]  Andreas Mortensen,et al.  Metal Matrix Composites in Industry: An Introduction and a Survey , 2003 .

[19]  Y. S. Tarng,et al.  An Investigation into Improving Worn Electrode Reliability in the Electrical Discharge Machining Process , 2000 .

[20]  Mukund R. Patel,et al.  Theoretical models of the electrical discharge machining process. II. The anode erosion model , 1989 .

[21]  W. D. Liu,et al.  Machining Characteristics of Al2O3/6061Al Composite using Rotary EDM with a Disklike Electrode , 2000 .

[22]  J. Deng,et al.  Introduction to Grey system theory , 1989 .

[23]  B. Yan,et al.  Study of added powder in kerosene for the micro-slit machining of titanium alloy using electro-discharge machining , 2000 .

[24]  F. Müller,et al.  Non-conventional machining of particle reinforced metal matrix composite , 2000 .

[25]  Mukund R. Patel,et al.  Theoretical models of the electrical discharge machining process. I. A simple cathode erosion model , 1989 .

[26]  V. M. Kevorkijan,et al.  Aluminum-base composites , 1999 .

[27]  Roberto Teti,et al.  Machining of Composite Materials , 2002 .

[28]  J. McGeough.  Advanced Methods Of Machining , 1988 .

[29]  Ko-Ta Chiang,et al.  Applying grey forecasting method for fitting and predicting the performance characteristics of an electro-conductive ceramic (Al2O3+30%TiC) during electrical discharge machining , 2007 .

[30]  T. R. Bement,et al.  Taguchi techniques for quality engineering , 1995 .

[31]  M. Taya,et al.  EDM machinability of SiCw/Alcomposites , 1989 .

[32]  C. F. Jeff Wu,et al.  Experiments: Planning, Analysis, and Parameter Design Optimization , 2000 .

[33]  B. Yan,et al.  Blind-hole drilling of Al2O3/6061Al composite using rotary electro-discharge machining , 2000 .

[34]  M. Ramulu,et al.  EDM sinker cutting of a ceramic particulate composite, SiC-TiB sub 2 , 1988 .

[35]  Agostino G. Bruzzone,et al.  Effect of Flushing and Electrode Material on Die Sinking EDM , 1999 .