Optimizing Bladder Resin Transfer Molding Process to Manufacture Complex, Thin-Ply Thermoplastic Tubular Composite Structures: An Experimental Case Study

The bladder molding process is primarily used in sporting applications but mostly with prepregs. Bladder-Assisted Resin Transfer Molding (B-RTM) presents the tremendous potential to automate and mass produce the complex hollow-composite profiles. Thin-ply, non-crimp fabrics (NCFs) provide excellent mechanical, fracture toughness, and vibration damping properties on top of the weight saving it offers to a final product. However, these fiber architectures are difficult to inject due to the resistance they provide for the polymer flow using the liquid injection process. Therefore, it is mandatory to optimize the process parameters to reduce the time for injection and simultaneously achieve better consolidation. This work presents a first, detailed, experimental case study to successfully inject a low-permeability, thin-ply, complex, thermoplastic tubular structure, and the effect of process parameters, boundary conditions, the associated manufacturing challenges, and proposed solutions are deliberated in this paper.

[1]  K. Leong,et al.  On the structural damping response of hollow carbon composite shafts with room temperature curable novel acrylic liquid thermoplastic resin , 2021, Composites Communications.

[2]  K. Leong,et al.  Development and impact characterization of acrylic thermoplastic composite bicycle helmet shell with improved safety and performance , 2021 .

[3]  K. Leong,et al.  Mechanical performance and damage mechanisms of thin rectangular carbon/ Elium® tubular thermoplastic composites under flexure and low-velocity impact , 2021 .

[4]  K. Leong,et al.  Manufacturing and investigating the load, energy and failure attributes of thin ply carbon/Elium® thermoplastic hollow composites under low-velocity impact , 2021 .

[5]  K. Leong,et al.  Damping, impact and flexural performance of novel carbon/Elium® thermoplastic tubular composites , 2020 .

[6]  Jinglei Yang,et al.  Low-velocity impact behaviors of a fully thermoplastic composite laminate fabricated with an innovative acrylic resin , 2020 .

[7]  K. Leong,et al.  Quasi-static indentation response of core-shell particle reinforced novel NCCF/Elium® composites at different feed rates , 2020 .

[8]  R. Barsotti,et al.  Investigation on Ultrasonic Welding Attributes of Novel Carbon/Elium® Composites , 2020, Materials.

[9]  Jinglei Yang,et al.  Enhanced Mode I fracture toughness of UHMWPE fabric/thermoplastic laminates with combined surface treatments of polydopamine and functionalized carbon nanotubes , 2019 .

[10]  M. Försth,et al.  Flammability, Smoke, Mechanical Behaviours and Morphology of Flame Retarded Natural Fibre/Elium® Composite , 2019, Materials.

[11]  S. Joshi,et al.  Energy Characteristics and Failure Mechanisms for Textile Spread Tow Thin Ply Thermoplastic Composites under Low-velocity Impact , 2019, Fibers and Polymers.

[12]  Aaron P. Stebner,et al.  Recycling glass fiber thermoplastic composites from wind turbine blades , 2019, Journal of Cleaner Production.

[13]  S. Joshi,et al.  Low-velocity impact response of carbon fibre composites with novel liquid Methylmethacrylate thermoplastic matrix , 2018, Composite Structures.

[14]  S. Joshi,et al.  Mode I fracture toughness and fractographic investigation of carbon fibre composites with liquid Methylmethacrylate thermoplastic matrix , 2018 .

[15]  S. Joshi,et al.  Enhanced vibration damping and dynamic mechanical characteristics of composites with novel pseudo-thermoset matrix system , 2017 .

[16]  R. Schledjewski,et al.  Influence of process pressures on filling behavior of tubular fabrics in bladder-assisted resin transfer molding , 2017 .

[17]  S. Joshi,et al.  Optimizing Polymer Infusion Process for Thin Ply Textile Composites with Novel Matrix System , 2017, Materials.

[18]  R. M. Boumbimba,et al.  Glass fibres reinforced acrylic thermoplastic resin-based tri-block copolymers composites: Low velocity impact response at various temperatures , 2017 .

[19]  S. Joshi,et al.  Experimental investigation on suitability of carbon fibre thin plies for racquets , 2016 .

[20]  Nuri Ersoy,et al.  A Review on the Mechanical Modeling of Composite Manufacturing Processes , 2016, Archives of Computational Methods in Engineering.

[21]  R. Schledjewski,et al.  Optical Permeability Measurement on Tubular Braided Reinforcing Textiles , 2015 .

[22]  S. Joshi,et al.  Design, Manufacturing and Testing of Filament Wound Composite Risers for Marine and Offshore Applications , 2015 .

[23]  Seung‐Hwan Chang,et al.  Evaluation of modeling techniques for a type III hydrogen pressure vessel (70 MPa) made of an aluminum liner and a thick carbon/epoxy composite for fuel cell vehicles , 2012 .

[24]  H. Ghiasi,et al.  Optimum Structural and Manufacturing Design of a Braided Hollow Composite Part , 2010 .

[25]  S. Tsai,et al.  Experimental studies of thin-ply laminated composites , 2007 .

[26]  Harald E.N. Bersee,et al.  Reactive processing of textile fiber-reinforced thermoplastic composites – An overview , 2007 .

[27]  C. Kaynak,et al.  Effects of Injection Pressure in Resin Transfer Moulding (RTM) of Woven Carbon Fibre/Epoxy Composites , 2006 .

[28]  F. Trochu,et al.  Analysis of the Consolidation in Flexible Bladder Process for Thin Composite Parts by Finite Element Method , 2000 .

[29]  W. Michaeli,et al.  Cores lead to an automated production of hollow composite parts in resin transfer moulding , 1998 .

[30]  R. Schledjewski,et al.  A methodology for determining preform compaction in bladder-assisted resin transfer molding with elastomeric bladders for tubular composite parts , 2019 .

[31]  Richard H Wiggins,et al.  Digital imaging. , 2003, Seminars in ultrasound, CT, and MR.

[32]  Antonio Langella,et al.  Analytical modelling of pressure bag technology , 1992 .