Effect of current collector corrosion made from printed circuit board (PCB) on the degradation of self-breathing direct methanol fuel cell stack

Abstract Adopting printed circuit board (PCB) as the current collector for direct methanol fuel cell (DMFC) is a promising task. This paper found that the combinational 10 μm Ni/2 μm Au coatings on PCB could not endure halide attacking in its anodic polarization. With this coated PCB, the self-breathing DMFC stack with passive methanol supply exhibited progressively degradation in its lifetime test. By using a series of measurements, it is shown that initial corrosion would not obviously influence stack degradation, but the subsequently inter-facilitation, between F − originating from Nafion membrane and corrosion products of Ni 2+ and Cu 2+ from PCB, would result in serious degradation, the final stack invalidation would present accompanied with the loss of membrane conductivity. The defects on coated PCB are crucial to initiate localized corrosion and stack degradation. Although cyclic voltammetry (CV) technology is effective to recover cell temporarily, its damage by releasing F − should be further evaluated.

[1]  Electrochemical chromic acid regeneration process with fuel-cell electrode assistance. Part I: Removal of contaminants , 2001 .

[2]  Toshiyuki Momma,et al.  Design and fabrication of pumpless small direct methanol fuel cells for portable applications , 2004 .

[3]  Tatsuhiro Okada,et al.  The Effect of Impurity Cations on the Oxygen Reduction Kinetics at Platinum Electrodes Covered with Perfluorinated Ionomer , 2001 .

[4]  T. Zhao,et al.  Preparation and characterization of a PtRu/C nanocatalyst for direct methanol fuel cells , 2005 .

[5]  Joghee Prabhuram,et al.  Preparation and the physical/electrochemical properties of a Pt/C nanocatalyst stabilized by citric acid for polymer electrolyte fuel cells , 2005 .

[6]  Tatsuhiro Okada,et al.  The Effect of Impurity Cations on the Transport Characteristics of Perfluorosulfonated Ionomer Membranes , 1999 .

[7]  A. Tasaka,et al.  Mechanism of film formation on nickel anodes in a molten NH4F·2HF , 1999 .

[8]  J. Besenhard,et al.  Conductivity of polymer electrolyte membranes by impedance spectroscopy with microelectrodes , 2005 .

[9]  A. Dermaj,et al.  Effect of (R+, X–) salts addition on nickel corrosion in 1M sulfuric acid medium , 2005 .

[10]  Effect of operation parameters on performance of micro direct methanol fuel cell fabricated on printed circuit board , 2006 .

[11]  Suk Won Cha,et al.  Development of portable fuel cell arrays with printed-circuit technology , 2003 .

[12]  B. Conway,et al.  Dissolution and passivation processes in the corrosion of copper and nickel in KF.2HF at 85 °C , 1997 .

[13]  Chenggang Xie,et al.  Development of a 2 W direct methanol fuel cell power source , 2004 .

[14]  B. Conway,et al.  Passivation and depassivation of Monel electrodes in KF.2HF melts in comparison with the behaviour of nickel , 1997 .

[15]  Huamin Zhang,et al.  Novel electrode structure for DMFC operated with liquid methanol , 2006 .

[16]  M. Noel,et al.  Electrochemistry of metals and semiconductors in fluoride media , 2005 .

[17]  Y. Shim,et al.  Square‐Wave Voltammetric Detection of Dopamine at a Copper‐(3‐Mercaptopropyl) Trimethoxy Silane Complex Modified Electrode , 2005 .

[18]  T. Zhao,et al.  Methanol adsorbates on the DMFC cathode and their effect on the cell performance , 2005 .

[19]  I. Milošev.  The effect of various halide ions on the passivity of Cu, Zn and Cu–xZn alloys in borate buffer , 2007 .

[20]  W. Lehnert,et al.  Current distribution mapping in polymer electrolyte fuel cells—A finite element analysis of measurement uncertainty imposed by lateral currents , 2006 .

[21]  T. Osaka,et al.  MEMS-based design and fabrication of a new concept micro direct methanol fuel cell (μ-DMFC) , 2004 .

[22]  Andreas Schmitz,et al.  Planar self-breathing fuel cells , 2003 .

[23]  L. Wan,et al.  In situ scanning tunneling microscopy of Cu(110): atomic structures of halide adlayers and anodic dissolution , 1999 .

[24]  M. De Francesco,et al.  Nafion degradation in PEFCs from end plate iron contamination , 2003 .

[25]  Michael Fowler,et al.  Mechanical properties of Nafion™ electrolyte membranes under hydrated conditions , 2005 .

[26]  C. Hebling,et al.  Stability of planar PEMFC in Printed Circuit Board technology , 2004 .

[27]  B. H. Loo,et al.  A study by voltammetry and the photocurrent response method of copper electrode behavior in acidic and alkaline solutions containing chloride ions , 1995 .

[28]  Mahlon Wilson,et al.  A printed circuit board approach to measuring current distribution in a fuel cell , 1998 .

[29]  Shulamith Schlick,et al.  Membrane-derived fluorinated radicals detected by electron spin resonance in UV-irradiated Nafion and Dow ionomers: effect of counterions and H2O2. , 2005, The journal of physical chemistry. B.

[30]  B. Yi,et al.  Studies on performance degradation of a direct methanol fuel cell (DMFC) in life test , 2004 .

[31]  T. Zhao,et al.  Development of PtRu-CeO2/C anode electrocatalyst for direct methanol fuel cells , 2006 .

[32]  Suli Wang,et al.  Improvement of direct methanol fuel cell performance by modifying catalyst coated membrane structure , 2005 .

[33]  G. Lindbergh,et al.  Adhesive copper films for an air-breathing polymer electrolyte fuel cell , 2005 .

[34]  R. Behm,et al.  In-situ STM study of the initial stages of corrosion of Cu(100) electrodes in sulfuric and hydrochloric acid solution , 1998 .

[35]  Changpeng Liu,et al.  Effect of cations in solution on the oxidation of methanol on the surface of platinum electrode , 2006 .

[36]  Tsutomu Ioroi,et al.  Dissolution of Nafion® membrane and recast Nafion® film in mixtures of methanol and water , 2004 .