Investigating the friction coefficient in functionally graded rapid prototyping of Al–Al2O3 composite prepared by fused deposition modelling

Purpose The present research work aims to study the friction coefficient in functionally graded rapid prototyping of Al–Al2O3 composite prepared via fused deposition modelling (FDM)-assisted investment casting (IC) process. The optimized settings of the process parameters (namely, filament proportion, volume of FDM pattern, density of FDM pattern, barrel finishing (BF) time, BF media weight and number of IC slurry layers) suggested in the present research work will help fabricate parts possessing higher frictional coefficient. Design/methodology/approach Initially, melt flow index (MFI) of two different proportions of Nylon6-Al–Al2O3 (to be used as an alternative FDM filament material) was tested on the melt flow indexer and matched with MFI of commercially used acrylonitrile–butadiene–styrene filament. After this, the selected proportions of Nylon6-Al–Al2O3 were prepared in the form of the FDM filament by using a single screw extruder. Further, this FDM filament has been used for developing sacrificial IC patterns in the existing FDM system which was barely finished to improve their surface finish. Castings developed were tested for their wear resistance properties on a pin-on-disc-type tribo-tester under dry conditions at sliding conditions to check their suitability as a frictional device for industrial applications. In the methodology part, Taguchi L18 orthogonal array was used to study the effect of selected process variables on the coefficient of friction (μ). Findings It has been found that filament proportion, volume of FDM pattern and density of FDM pattern have significantly affected the μ-values. Further, density of the FDM pattern was found to have 91.62 per cent contribution in obtaining μ-values. Scanning electron micrographs highlighted uniform distribution of Al2O3 particles in the Al-matrix at suggested optimized settings. Practical implications The present methodology shows the development of a functional graded material that consisted of surface reinforcement with Al2O3 particles, which could have applications for manufacturing friction surfaces such as clutch plates, brake drum, etc. Originality/value This paper describes the effect of process parameters on wear properties of the Al–Al2O3 composite developed as a functionally graded material by the FDM-based pattern in the IC process.

[1]  Alberto Boschetto,et al.  Modelling micro geometrical profiles in fused deposition process , 2012 .

[2]  M. Balasubramanian,et al.  Introduction to Composites , 2013 .

[3]  Pranjal Jain,et al.  ScienceDirect The Manufacturing Engineering Society International Conference , MESIC 2013 Feasibility Study of manufacturing using rapid prototyping : FDM Approach , 2013 .

[4]  Simon C. Tung,et al.  Automotive tribology overview of current advances and challenges for the future , 2004 .

[5]  S. Das,et al.  Analysis of stir die cast Al–SiC composite brake drums based on coefficient of friction , 2012 .

[6]  K. Das,et al.  Abrasive wear of zircon sand and alumina reinforced Al–4.5 wt%Cu alloy matrix composites – A comparative study , 2007 .

[7]  S. Buytoz,et al.  Abrasive wear of Al2O3-reinforced aluminium-based MMCs , 2001 .

[8]  G. Kumar,et al.  Mechanical and Tribological Behavior of Particulate Reinforced Aluminum Metal Matrix Composites – a review , 2011 .

[9]  Rupinder Singh,et al.  Wear modelling of Al-Al2O3 functionally graded material prepared by FDM assisted investment castings using dimensionless analysis , 2015 .

[10]  Hossein Abdizadeh,et al.  Development of high-performance A356/nano-Al2O3 composites , 2009 .

[11]  Luigi Maria Galantucci,et al.  Quantitative analysis of a chemical treatment to reduce roughness of parts fabricated using fused deposition modeling , 2010 .

[12]  T. Miyajima,et al.  Effects of reinforcements on sliding wear behavior of aluminum matrix composites , 2003 .

[13]  Blaža Stojanović,et al.  Tribological properties of A356 Al-Si alloy composites under dry sliding conditions , 2014 .

[14]  Wan Sharuzi Wan Harun,et al.  Evaluation of ABS patterns produced from FDM for investment casting process , 2009 .

[15]  Rupinder Singh,et al.  Effect of process parameters on surface hardness, dimensional accuracy and surface roughness of investment cast components , 2013 .

[16]  M. Surappa,et al.  Dry sliding wear behavior of Al2O3 fiber reinforced aluminum composites , 2000 .

[17]  Jianfeng Huang,et al.  Effects of carbon fiber length on the tribological properties of paper-based friction materials , 2014 .

[18]  J. Rödel,et al.  Wear Properties of Alumina/Aluminum Composites with Interpenetrating Networks , 1996 .

[19]  Nagnath U. Kakde,et al.  Development of customized innovative product using Fused Deposition Modeling technique of Rapid Prototyping and Investment Casting , 2012 .

[20]  N. Radhika,et al.  Dry sliding wear behaviour of aluminium/alumina/graphite hybrid metal matrix composites , 2012 .

[21]  E. J. Herrera,et al.  Dry and lubricated wear resistance of mechanically-alloyed aluminium-base sintered composites , 2001 .

[22]  S. Prasad,et al.  Aluminum Metal-Matrix Composites for Automotive Applications: Tribological Considerations , 2004 .

[23]  M. Meratian,et al.  Fabrication of in situ aluminum–alumina composite with glass powder , 2009 .

[24]  S. F. Moustafa.  Wear and wear mechanisms of Al-22%Si/A12O3f composite , 1995 .

[25]  A. Elaya Perumal,et al.  Study on mechanical and wear properties of Al 7075/Al2O3/graphite hybrid composites , 2014 .

[26]  Seyed Mojtaba Zebarjad,et al.  The effects of volume percent and aspect ratio of carbon fiber on , 2008 .

[27]  Chee Kai Chua,et al.  Rapid prototyping and tooling techniques: a review of applications for rapid investment casting , 2005 .

[28]  Barbara Previtali,et al.  Application of traditional investment casting process to aluminium matrix composites , 2008 .

[29]  T. Sornakumar,et al.  Friction and wear studies of die cast aluminum alloy‐aluminum oxide‐reinforced composites , 2010 .

[30]  M. Gupta,et al.  Effect of submicron size Al2O3 particulates on microstructural and tensile properties of elemental Mg , 2008 .

[31]  Ian M. Hutchings,et al.  Wear of alumina fibre–aluminium metal matrix composites by two-body abrasion , 1989 .

[32]  Development of low cost metal matrix composites for commercial applications , 2000 .

[33]  Seyed Mojtaba Zebarjad,et al.  Dependency of physical and mechanical properties of mechanical alloyed Al–Al2O3 composite on milling time , 2007 .

[34]  Chee Kai Chua,et al.  Rapid investment casting: direct and indirect approaches via fused deposition modelling , 2004 .

[35]  K. Woo,et al.  Fabrication of Al alloy matrix composite reinforced with subsive-sized Al2O3 particles by the in situ displacement reaction using high-energy ball-milled powder , 2007 .

[36]  Luigi Maria Galantucci,et al.  Experimental study aiming to enhance the surface finish of fused deposition modeled parts , 2009 .