Stencil Printing Optimization using a Hybrid of Support Vector Regression and Mixed-integer Linear Programming

Abstract This research proposes an optimization approach to enhance the stencil printing process (SPP) in surface mount printed circuit board (PCB) assembly. Stencil printing behavior is affected by many variables including stencil design, solder paste composition, squeegee speed and pressure, and other environmental conditions. In this research, support vector regression (SVR) model is trained to capture the complex relationships among these variables, based on historical data. A mixed-integer linear programming (MILP) model is proposed to minimize the total absolute predicted deviation of average volume transfer from target. The optimal printing settings are retrieved for different sample problems with low computational cost.

[1]  Andreas Ostmann,et al.  Technical challenges of stencil printing technology for ultra fine pitch flip chip bumping , 2004, Microelectron. Reliab..

[2]  Ndy Ekere,et al.  Rheological characterisation and printing performance of Sn/Ag/Cu solder pastes , 2009 .

[3]  R. Durairaj,et al.  Critical factors affecting paste flow during the stencil printing of solder paste , 2001 .

[4]  Anu Maria,et al.  Engineering solder paste performance through controlled stress rheology analysis , 1998 .

[5]  J. A. Owczarek,et al.  A study of the off-contact screen printing process. II. Analysis of the model of the printing process , 1990 .

[6]  Ndy Ekere,et al.  PARAMETER INTERACTIONS IN STENCIL PRINTING OF SOLDER PASTE , 1996 .

[7]  Ahmad Lotfi,et al.  Industrial Application of Fuzzy Systems: Adaptive Fuzzy Control od Solder Paste Stencil Printing , 1998, Inf. Sci..

[8]  Nduka Nnamdi (Ndy) Ekere,et al.  The behavior of solder pastes in stencil printing with vibrating squeegee , 1998, IEEE Transactions on Components, Packaging, and Manufacturing Technology: Part C.

[9]  J. Rene Villalobos,et al.  Using fixed and adaptive multivariate SPC charts for online SMD assembly monitoring , 2005 .

[10]  Tsung-Nan Tsai.  Development of an integrated reflow soldering control system using incremental hybrid process knowledge , 2005, Expert Syst. Appl..

[11]  H. W. Markstein.  CONTROLLING THE VARIABLES IN STENCIL PRINTING , 1997 .

[12]  Russell P. Kraft,et al.  Designed experiments to analyze the solder joint quality output of a SMD remanufacturing system , 1996, Nineteenth IEEE/CPMT International Electronics Manufacturing Technology Symposium.

[13]  V. Vapnik.  Pattern recognition using generalized portrait method , 1963 .

[14]  Tsung-Nan Tsai,et al.  Improving the fine-pitch stencil printing capability using the Taguchi method and Taguchi fuzzy-based model , 2011 .

[15]  Ndy Ekere,et al.  Sub process challenges in ultra fine pitch stencil printing of type‐6 and type‐7 Pb‐free solder pastes for flip chip assembly applications , 2005 .

[16]  Ndy Ekere,et al.  Process Modelling Maps for Solder Paste Printing , 1994 .

[17]  Douglas C. Montgomery,et al.  Using statistically designed experiments for process development and improvement: an application in electronics manufacturing , 2000 .

[18]  Ndy Ekere,et al.  The rheological properties of solder and solar pastes and the effect on stencil printing , 2000 .

[19]  A. Goldstein,et al.  Stencil Printing Process Modeling and Control Using Statistical Neural Networks , 2008, IEEE Transactions on Electronics Packaging Manufacturing.

[20]  M. Whitmore,et al.  PLASTIC STENCILS FOR BOTTOM-SIDE CHIP ATTACH , 1997 .

[21]  Francis K. H. Lau,et al.  A hierarchical evaluation of the solder paste printing process , 1997 .

[22]  Emeka H. Amalu,et al.  Evaluation of rheological properties of lead-free solder pastes and their relationship with transfer efficiency during stencil printing process , 2011 .

[23]  D. Basak,et al.  Support Vector Regression , 2008 .

[24]  R. Storer,et al.  Critical variables of solder paste stencil printing for micro-BGA and fine-pitch QFP , 2004, IEEE Transactions on Electronics Packaging Manufacturing.

[25]  J C Y Huang,et al.  Reducing Solder Paste Inspection in Surface-Mount Assembly Through Mahalanobis–Taguchi Analysis , 2010, IEEE Transactions on Electronics Packaging Manufacturing.

[26]  Taho Yang,et al.  A neural network-based prediction model for fine pitch stencil-printing quality in surface mount assembly , 2005, Eng. Appl. Artif. Intell..

[27]  Tsung-Nan Tsai,et al.  Modeling and optimization of stencil printing operations: A comparison study , 2008, Comput. Ind. Eng..

[28]  Ndy Ekere,et al.  Squeegee deformation study in the stencil printing of solder pastes , 1994 .