One-dimensional thermal model of cold-start in a polymer electrolyte fuel cell stack

A transient, one-dimensional thermal model for a generic polymer electrolyte fuel cell (PEFC) stack is developed to investigate the cold-start ability and the corresponding energy requirement over different operating and ambient conditions. The model is constructed by applying the conservation of energy on each stack component and connecting the component's relevant boundaries to form a continuous thermal model. The phase change of ice and re-circulation of coolant flow are included in the analytical framework and their contribution to the stack thermal mass and temperature distribution of the components is also explored. A parametric study was conducted to determine the governing parameters, relative impact of the thermal mass of each stack component and ice, and anticipated temperature distribution in the stack at start-up for various operating conditions. Results indicate that 20 cells were sufficient to accurately experimentally and computationally simulate the full size stack behavior. It was observed that an optimum range of operating current density exists for a chosen stack design, in which rapid start-up of the stack from sub-zero condition can be achieved. Thermal isolation of the stack at the end plates is recommended to reduce the start-up time. Additionally, an end plate thickness exceeding a threshold value has no added effect on the stack cold-start ability. Effect of various internal and external heating mechanisms on the stack start-up were also investigated, and flow of heated coolant above 0 °C was found to be the most effective way to achieve the rapid start-up.

[1]  V. Voller,et al.  ERAL SOURCE-BASED METHOD FOR SOLIDIFICATION PHASE CHANGE , 1991 .

[2]  R. M. Moore,et al.  Polymer electrolyte fuel cell stack thermal model to evaluate sub-freezing startup , 2005 .

[3]  In-Hwan Oh,et al.  Characteristics of the PEMFC Repetitively Brought to Temperatures below 0°C , 2003 .

[4]  S. Patankar.  Numerical Heat Transfer and Fluid Flow , 2018, Lecture Notes in Mechanical Engineering.

[5]  R. Ahluwalia,et al.  Fuel Cell Systems Analysis , 2003 .

[6]  Xianguo Li,et al.  Effect of flow and temperature distribution on the performance of a PEM fuel cell stack , 2006 .

[7]  Allen J. Bard,et al.  Electrochemical Methods: Fundamentals and Applications , 1980 .

[8]  Rajesh K. Ahluwalia,et al.  Rapid self-start of polymer electrolyte fuel cell stacks from subfreezing temperatures , 2006 .

[9]  Biao Zhou,et al.  Water and thermal management for Ballard PEM fuel cell stack , 2005 .

[10]  Y. Zong,et al.  Water and thermal management in a single PEM fuel cell with non-uniform stack temperature , 2006 .

[11]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[12]  M. Mench,et al.  Direct measurement of through-plane thermal conductivity and contact resistance in fuel cell materials , 2006 .

[13]  Jack S. Brenizer,et al.  Quantification of liquid water accumulation and distribution in a polymer electrolyte fuel cell using neutron imaging , 2006 .

[14]  Suhao He,et al.  One-Dimensional Transient Model for Frost Heave in Polymer Electrolyte Fuel Cells I. Physical Model , 2006 .

[15]  Song-Yul Choe,et al.  Unsteady 2D PEM fuel cell modeling for a stack emphasizing thermal effects , 2007 .

[16]  Markku J. Lampinen,et al.  Analysis of Free Energy and Entropy Changes for Half‐Cell Reactions , 1993 .

[17]  Hossein Toghiani,et al.  Effect of sub-freezing temperatures on a PEM fuel cell performance, startup and fuel cell components , 2006 .

[18]  Keith Scott,et al.  One-dimensional thermal model for direct methanol fuel cell stacks. Part I. Model development , 1999 .

[19]  G. Maggio,et al.  Modelling of temperature distribution in a solid polymer electrolyte fuel cell stack , 1996 .

[20]  Tomohiro Ogawa,et al.  The Design and Performance of a PEFC at a Temperature Below Freezing , 2004 .

[21]  Ned Djilali,et al.  THREE-DIMENSIONAL COMPUTATIONAL ANALYSIS OF TRANSPORT PHENOMENA IN A PEM FUEL CELL , 2002 .

[22]  Song-Yul Choe,et al.  Modeling and simulation of a PEM fuel cell stack considering temperature effects , 2006 .

[23]  Ralph E. White,et al.  A water and heat management model for proton-exchange-membrane fuel cells , 1993 .