An investigation of the tribological interaction between die damage and billet deformation during MMC extrusion

Abstract This study deals with material flow behaviour during the extrusion process of a metal-matrix composite (MMC), and the effects of this behaviour on the damage to die flat surfaces. AA 6063 aluminium matrix composite billets reinforced with SiC particles (167 μm) were prepared using the stir-casting method for extrusion. Extrusion of the MMC billets were conducted at 500 °C with a ram speed of 2 mm s−1 and an extrusion ratio of 25:1 under laboratory conditions. The extrusion die with two different channel profiles was manufactured from AISI H13 steel that was hardened, tempered and grounded. The flow patterns of the deformed billet during the MMC extrusion determine the positions of the SiC particles in the deformation zone. While some of the SiC particles flow within the deformed material, some flow at the deformed billet surface; these SiC particles play the most important role in the damage mechanism of the die-bearing surface and the geometry of the dead metal zone (DMZ). The possible damage to the die-bearing surfaces is severe at the entrance of the die bearing. On the other hand, some SiC particles are broken in this zone due to the severe deformation stress of the MMC billet.

[1]  Recep Ekici,et al.  Investigation of impact behaviour of aluminium based SiC particle reinforced metal–matrix composites , 2007 .

[2]  M. Surappa.  On the nature of particle flow during extrusion of cast 6061 Al/SiCP composites , 1993 .

[3]  A. Taşdemirci,et al.  Analyses of metallurgical behavior of Al–SiCp composites after ballistic impacts , 2004 .

[4]  A. Borrego,et al.  Calorimetric study of 6061-Al–15 vol.% SiCw PM composites extruded at different temperatures , 1998 .

[5]  P. Liaw,et al.  Effects of Particle Orientation in Silicon Carbide Particulate Reinforced Aluminum Matrix Composite Extrusions on Ultrasonic Velocity Measurement , 1995 .

[6]  Fionn P.E. Dunne,et al.  Modelling central bursting in the extrusion of particulate reinforced metal matrix composite materials , 1997 .

[7]  Farghalli A. Mohamed,et al.  Particulate reinforced metal matrix composites — a review , 1991, Journal of Materials Science.

[8]  Mario Rosso,et al.  Ceramic and metal matrix composites: Routes and properties , 2006 .

[9]  B. Dodd,et al.  Room temperature formability of particle-reinforced metal matrix composites: forging, extrusion and deep drawing , 1995 .

[10]  O. P. Grover,et al.  Extrusion characteristics of aluminium alloy/SiCpmetal matrix composites , 1999 .

[11]  M. Surappa,et al.  Tribological behavior of Al–Si–SiCp composites/automobile brake pad system under dry sliding conditions , 2007 .

[12]  M. Karamiş,et al.  Surface characteristics of projectiles after frictional interaction with metal matrix composites under ballistic condition , 2006 .

[13]  M. Surappa,et al.  Particle redistribution and matrix microstructure evolution during hot extrusion of cast SiCp reinforced aluminium alloy matrix composites , 1998 .

[14]  I. Flitta,et al.  Nature of friction in extrusion process and its effect on material flow , 2003 .

[15]  P. K. Rohatgi,et al.  Deformation of graphite during hot extrusion of cast aluminum-silicon-graphite particle composites , 1984 .

[16]  E. Candan,et al.  Abrasive wear behavior and mechanical properties of Al-Si/SiC composites , 2004 .

[17]  Fehmi Nair,et al.  Effects of reinforcement particle size in MMCs on extrusion die wear , 2008 .

[18]  Manoj Gupta,et al.  Effect of limited matrix–reinforcement interfacial reaction on enhancing the mechanical properties of aluminium–silicon carbide composites , 2001 .

[19]  Jien-Wei Yeh,et al.  Study of 6061-Al2O3p composites produced by reciprocating extrusion , 2000 .

[20]  Li Cheng,et al.  Effect of reinforcement volume fraction on the evolution of reinforcement size during the extrusion of Al-SiC composites , 2002 .

[21]  M.S.J. Hashmi,et al.  Metal matrix composites: production by the stir casting method , 1999 .

[22]  B. Bacroix,et al.  Influence of microstructures and particle concentrations on the development of extrusion textures in metal matrix composites , 1995 .

[23]  M. Lieblich,et al.  Extrudability of PM 2124/SiCp aluminium matrix composite , 1997 .

[24]  Jie Zhou,et al.  Application of threedimensional numerical simulation to analysis of development of deformation zone at beginning of aluminium extrusion process , 2001 .

[25]  C. Kang,et al.  The effect of die shape on the hot extrudability and mechanical properties of 6061 Al/Al2O3 composites , 2000 .

[26]  W. Yanwen,et al.  Plastic working and superplasticity in aluminium–matrix composites reinforced with SiC particulates , 1998 .

[27]  M. Tan,et al.  Powder metal matrix composites: selection and processing , 1998 .

[28]  J. Yeh,et al.  An in situ composite of Al (graphite, Al4C3) produced by reciprocating extrusion , 2000 .

[29]  C. Kang,et al.  Effects of hot extrusion through a curved die on the mechanical properties of SiCp/Al composites fabricated by melt-stirring , 1999 .

[30]  Y. Murakoshi,et al.  Microstructures and mechanical properties of Al-Li/SiCp composite produced by extrusion processing , 1997 .

[31]  H. Mcqueen,et al.  Modelling extrusion of 2618 aluminium alloy and 2618-1 10%AI203 and 2618-20%AI203 composites , 1998 .

[32]  H. Cimenoglu,et al.  Tribological behavior of squeeze cast aluminum matrix composites , 2008 .

[33]  I. V. Samarasekera,et al.  Mathematical modeling of the extrusion of 6061/Al2O3/20p composite , 1996 .

[34]  D. Miracle.  Metal matrix composites – From science to technological significance , 2005 .