Microstructural analysis of varistors prepared from nanosize ZnO

Abstract ZnO nanoparticles were prepared by a solid state pyrolysis reaction of zinc acetate dihydrate and oxalic acid dihydrate at 500°C. The course of reaction at various temperatures was followed by XRD. Subsequently varistors were fabricated from this nano-ZnO material by solid state mixing with various oxide additives and sintering to 1050°C. The microstructure of the sintered material was studied using XRD, field emission SEM (FESEM), and EDX, and ZnO grains, bismuth rich regions and spinel phases were identified. Discs made from oxide doped nanoZnO show considerably higher breakdown voltage (656 ± 30 V mm-1) compared to those prepared from micrometre sized ZnO (410 ± 30 V mm-1) and commercial varistors (454 ± 30 V mm-1). However, varistors made from the nano-ZnO show very low densification and high leakage current, making them unsuitable for device fabrication.

[1]  A. Banerjee,et al.  Smart technique for fabrication of zinc oxide varistor , 2001 .

[2]  Suresh C. Pillai,et al.  The Effect of Processing Conditions on Varistors Prepared From Nanocrystalline ZnO , 2003 .

[3]  R. N. Viswanath,et al.  Preparation and characterization of nanocrystalline ZnO based materials for varistor applications , 1995 .

[4]  R. Speyer,et al.  Effect of rate controlled sintering on microstructure and electrical properties of ZnO doped with bismuth and antimony oxides , 1997 .

[5]  J. Tartaj,et al.  Sintering Behavior and Electrical Properties of Nanosized Doped‐ZnO Powders Produced by Metallorganic Polymeric Processing , 2004 .

[6]  J. Binner,et al.  Microwave Sintering of Nanometer and Micrometer Ferrite Powders , 1999 .

[7]  T. Gupta.  Application of Zinc Oxide Varistors , 1990 .

[8]  D. Shah,et al.  Effect of process variables on the grain growth and microstructure of ZnO–Bi2O3 varistors and their nanosize ZnO precursors , 1995 .

[9]  M. Inada.  Formation Mechanism of Nonohmic Zinc Oxide Ceramics , 1980 .

[10]  Zhongtai Zhang,et al.  Characterisation of ZnO-based varistors prepared from nanometre Precursor powders , 1999 .

[11]  Analysis of ZnO varistors prepared from nanosize ZnO precursors , 1998 .

[12]  I. Chen,et al.  Sintering dense nanocrystalline ceramics without final-stage grain growth , 2000, Nature.

[13]  Shenggang Yan,et al.  Low-temperature synthesis of ZnO nanoparticles by solid-state pyrolytic reaction , 2002 .

[14]  H. Wong,et al.  Effects of additives and secondary phases on the sintering behavior of zinc oxide-based varistors , 2000 .

[15]  Ziyu Wu,et al.  Synthesis and evolution of rod-like nano-scaled ZnC2O4·2H2O whiskers to ZnO nanoparticles , 2003 .

[16]  M. Nygren,et al.  Preparation of ZnO-based varistors by the sol–gel technique , 1994 .

[17]  M. Castro,et al.  Electrical properties of ZnO-based varistors prepared by combustion synthesis , 2002 .

[18]  J. Tartaj,et al.  Low-temperature fully dense and electrical properties of doped-ZnO varistors by a polymerized complex method , 2002 .

[19]  M. Matsuoka.  Nonohmic Properties of Zinc Oxide Ceramics , 1971 .

[20]  Yao Yao,et al.  Zino Oxide Varistors Made from Powders Prepared by Amine Processing , 1989 .

[21]  D. Shah,et al.  Microemulsion mediated synthesis of zinc-oxide nanoparticles for varistor studies , 1993 .

[22]  Anthony R. West,et al.  Solid State Chemistry and its Applications , 1984 .