Preparation of beeswax/multi-walled carbon nanotubes as novel shape-stable nanocomposite phase-change material for thermal energy storage

Abstract Development of phase-change material (PCM) as thermal energy storage for building envelopes is promising for energy utilization. However, there are two major drawbacks of PCM application, which are low thermal conductivity and high-volume reduction due to phase-change transition. One solution is to develop a shape-stabilized phase-change material (SSPCM) as a composite that is able to prevent leakage during the transition from solid to liquid. Therefore, the objective of this study is to prepare beeswax/multi-walled carbon nanotubes as form-stable nanocomposite phase-change material for thermal energy storage, based on previously unattempted methods. Beeswax was being used as PCM because of its high latent heat and multi-walled carbon nanotubes (MWCNTs) as supporting material with high thermal conductivity. There are three types of MWCNTs applied in this research: pristine MWCNTs, ball-milled MWCNTs and acid-treated MWCNTs. Beeswax/CNT composite samples were prepared with ratios of 5 and 20 wt%. Composite samples were tested from structure modification and thermal performance, including latent heat, sensible heat, melting point, solidifying point, thermal conductivity, and thermal-cycle testing for up to 300 cycles. Experimental results showed that thermal conductivity of novel shape-stable nanocomposite PCM increased by a factor of 2 and there was no significant phase transition in the melting or solidifying temperature. The high heat storage capability and thermal conductivity of nanocomposite PCM enable it to be a potential material for thermal energy storage in practical applications.

[1]  Benxia Li,et al.  Stearic-acid/carbon-nanotube composites with tailored shape-stabilized phase transitions and light–heat conversion for thermal energy storage , 2015 .

[2]  Huaqing Xie,et al.  Increasing the thermal conductivity of palmitic acid by the addition of carbon nanotubes , 2010 .

[3]  A. Kuhe,et al.  Distillate Yield Improvement using a Parabolic Dish Reflector Coupled Single Slope Basin Solar Still with Thermal Energy Storage using Beeswax , 2016 .

[4]  Luisa F. Cabeza,et al.  Review on thermal energy storage with phase change: materials, heat transfer analysis and applications , 2003 .

[5]  Teuku Meurah Indra Mahlia,et al.  Modeling and simulation of the energy use in an occupied residential building in cold climate , 2012 .

[6]  Dan Zhou,et al.  Review on thermal energy storage with phase change materials (PCMs) in building applications , 2012 .

[7]  Jesús Lizana,et al.  Advances in thermal energy storage materials and their applications towards zero energy buildings: A critical review , 2017 .

[8]  Jungki Seo,et al.  Performance evaluation of the microencapsulated PCM for wood-based flooring application , 2012 .

[9]  Peng Zhang,et al.  Preparation and thermal characterization of paraffin/metal foam composite phase change material , 2013 .

[10]  Xiangfei Kong,et al.  Building Energy Storage Panel Based on Paraffin/Expanded Perlite: Preparation and Thermal Performance Study , 2016, Materials.

[11]  Jinhong Li,et al.  Pore structure modified diatomite-supported PEG composites for thermal energy storage , 2016, Scientific Reports.

[12]  Alessandro Romagnoli,et al.  Application of material assessment methodology in latent heat thermal energy storage for waste heat recovery , 2017 .

[13]  Luisa F. Cabeza,et al.  Simulation-based optimization of PCM melting temperature to improve the energy performance in buildings , 2017 .

[14]  S. C. Kaushik,et al.  DEVELOPMENT OF PHASE CHANGE MATERIALS BASED MICROENCAPSULATED TECHNOLOGY FOR BUILDINGS: A REVIEW , 2011 .

[15]  Luisa F. Cabeza,et al.  Materials used as PCM in thermal energy storage in buildings: A review , 2011 .

[16]  A. Sharma,et al.  Review on thermal energy storage with phase change materials and applications , 2009 .

[17]  M. Fang,et al.  Enhanced thermal properties of novel shape-stabilized PEG composite phase change materials with radial mesoporous silica sphere for thermal energy storage , 2015, Scientific Reports.

[18]  Luis Pérez-Lombard,et al.  A review on buildings energy consumption information , 2008 .

[19]  Jing Ding,et al.  Enhanced thermal conductivity of ternary carbonate salt phase change material with Mg particles for solar thermal energy storage , 2017 .

[20]  Khamid Mahkamov,et al.  Solar energy storage using phase change materials , 2007 .

[21]  N. Putra,et al.  THERMAL PROPERTIES OF BEESWAX/CuO NANO PHASE-CHANGE MATERIAL USED FOR THERMAL ENERGY STORAGE , 2016 .

[22]  M. A. Medina,et al.  Assessing the integration of a thin phase change material (PCM) layer in a residential building wall for heat transfer reduction and management , 2015 .

[23]  Ruzhu Wang,et al.  Thermal energy storage coupled with PV panels for demand side management of industrial building cooling loads , 2017 .

[24]  Paul Cooper,et al.  Hybrid model predictive control of a residential HVAC system with on-site thermal energy generation and storage , 2017 .

[25]  G. Fang,et al.  Thermal properties and morphologies of MA–SA eutectics/CNTs as composite PCMs in thermal energy storage , 2016 .

[26]  R. Velraj,et al.  Phase change material-based building architecture for thermal management in residential and commercial establishments , 2008 .

[27]  G. Fang,et al.  Preparation, thermal properties and applications of shape-stabilized thermal energy storage materials , 2014 .

[28]  T. Mahlia,et al.  Effect of carbon nanospheres on shape stabilization and thermal behavior of phase change materials for thermal energy storage , 2014 .

[29]  A. Abhat.  Short term thermal energy storage , 1981 .

[30]  Ruzhu Wang,et al.  Enhancement of heat transfer for thermal energy storage application using stearic acid nanocomposite with multi-walled carbon nanotubes , 2013 .

[31]  K. Pielichowski,et al.  Phase change materials for thermal energy storage , 2014 .

[32]  Wen Tong Chong,et al.  Experimental study on performance and exhaust emissions of a diesel engine fuelled with Ceiba pentandra biodiesel blends , 2013 .

[33]  Lixian Sun,et al.  Preparation and thermal properties of fatty acids/CNTs composite as shape-stabilized phase change materials , 2012, Journal of Thermal Analysis and Calorimetry.

[34]  N. Putra,et al.  The utilization of paraffin and beeswax as heat energy storage in infant incubator , 2016 .

[35]  Yuhan Du,et al.  Comparison of the effect of various carbon fillers in the paraffin-based phase change materials------A Review , 2015, ICME 2015.

[36]  Jisoo Jeon,et al.  Preparation and evaluation of thermal enhanced silica fume by incorporating organic PCM, for application to concrete , 2013 .

[37]  T. Mahlia,et al.  Thermal properties of beeswax/graphene phase change material as energy storage for building applications , 2017 .

[38]  A. Sasmito,et al.  Numerical investigation of heat transfer performance of a rotating latent heat thermal energy storage , 2017, Applied Energy.

[39]  Luisa F. Cabeza,et al.  Building integration of PCM for natural cooling of buildings , 2013 .

[40]  Xin Qian,et al.  Measurement Techniques for Thermal Conductivity and Interfacial Thermal Conductance of Bulk and Thin Film Materials , 2016 .

[41]  L. Stobiński,et al.  Multiwall carbon nanotubes purification and oxidation by nitric acid studied by the FTIR and electron spectroscopy methods , 2010 .