Stamp forming of carbon fibre/PA12 composites – A comparison of a reactive impregnation process and a commingled yarn system

Two forms of carbon fibre reinforced polyamide 12 (PA12) were compared during non-isothermal stamp forming. The first was a stretch broken commingled yarn woven into a fabric, studied at three initial preconsolidation levels. The second was produced by in situ anionic polymerisation of lactam 12 (APLC12) in a carbon fibre textile, using a thermoplastic resin transfer moulding (TP-RTM) process. A processing window was defined for TP-RTM based upon non-isothermal polymerisation kinetics. For each material form, the effects of stamping parameters on flat plaque properties were examined. For commingled materials, the influence of preheat temperature and the initial preconsolidation level dominated, with preconsolidated materials deconsolidating strongly during the preheat cycle. For CF/APLC12 materials, the effect of material temperature and tool temperature dominated and reduced deconsolidation occurred. Hemisphere forming was enabled by stretch-broken yarn but was possible for both material classes. Over-injection moulding of recompounded CF/APLC12 composite onto stamped CF/APLC12 plate was performed, demonstrating a closed-loop recycling process.

[1]  J. Månson,et al.  A Model for the Consolidation of Aligned Thermoplastic Powder Impregnated Composites , 1995 .

[2]  Michael S. Saccucci,et al.  Engineering, Quality and Experimental Design , 1992 .

[3]  Jan-Anders E. Månson,et al.  Reaction injection pultrusion of PA12 composites: process and modelling , 2003 .

[4]  Conchur O Bradaigh,et al.  Process investigation of a liquid PA-12/carbon fibre moulding system , 2001 .

[5]  R. Kruse,et al.  Polyamides from lactams via anionic ring-opening polymerization : 2. Kinetics , 1997 .

[6]  Michael D. Gilchrist,et al.  Manufacturing of Thermoplastic Composites from Commingled Yarns-A Review , 1998 .

[7]  K. Friedrich,et al.  A new model for impregnation mechanisms in different GF/PP commingled yarns , 1994 .

[8]  Anthony Kelly,et al.  Comprehensive composite materials , 1999 .

[9]  A. Long,et al.  Experimental characterisation of the consolidation of a commingled glass/polypropylene composite , 2001 .

[10]  A. Long,et al.  A Simulation of Reinforcement Deformation during the Production of Preforms for Liquid Moulding Processes , 1994 .

[11]  Jan-Anders E. Månson,et al.  Initiation mechanisms of an anionic ring‐opening polymerization of lactam‐12 , 2002 .

[12]  D. Bigg,et al.  Stamping of thermoplastic matrix composites , 1989 .

[13]  P. McDonnell,et al.  Processing and mechanical properties evaluation of a commingled carbon-fibre/PA-12 composite ☆ , 2001 .

[14]  Jan-Anders E. Månson,et al.  Time-temperature-transformation diagram for reactive processing of polyamide 12 , 2001 .

[15]  V. Michaud,et al.  An Impregnation Model for the Consolidation of Thermoplastic Composites Made from Commingled Yarns , 1999 .

[16]  Andrew C. Long,et al.  Compression moulding of glass and polypropylene composites for optimised macro- and micro- mechanical properties - 1. commingled glass and polypropylene , 1998 .

[17]  P. Ermanni,et al.  A combined impregnation and heat transfer model for stamp forming of unconsolidated commingled yarn preforms , 2004 .

[18]  K. Lahteenkorva,et al.  The Influence of Melt Impregnation Parameters on the Degree of Impregnation of a Polypropylene/Glass Fibre Prepreg , 1992 .

[19]  L. Robroek.  The development of rubber forming as a rapid thermoforming technique for continuous fibre reinforced thermoplastic composites: Quality control by process control , 1994 .

[20]  L. Ye,et al.  Consolidation of GF/PP commingled yarn composites , 1994 .

[21]  Rudolf Stauber,et al.  Plastics in automotive engineering , 2007 .

[22]  Andrew C. Long,et al.  Design and manufacture of textile composites , 2005 .

[23]  I. Verpoest,et al.  Optimisation of a GMT-based cold pressing technique for low cost textile reinforced thermoplastic composites , 1999 .

[24]  Andrew C. Long,et al.  Liquid Moulding Technologies , 1997 .

[25]  C. Plummer,et al.  Fusion bonding of polyamide 12 , 2001 .

[26]  M. Keefe,et al.  The draping and consolidation of commingled fabrics , 1991 .

[27]  V. Michaud,et al.  Commingled yarn composites for rapid processing of complex shapes , 2001 .